NI 9215 Datasheet
• BNC, screw-terminal, or spring-terminal connectivity • 250 Vrms, CAT II, channel-to-earth isolation (screw terminal); 60 VDC, CAT I, channel-to-earth isolation (BNC) The NI 9215 is an analog input module for use with NI CompactDAQ and CompactRIO systems. The NI 9215 includes four simultaneously sampled analog input channels and
Download NI 9215 Datasheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Using Acoustic Beamforming for Pass-By Noise …
www.ni.comUsing Acoustic Beamforming . for Pass-By Noise Source Detection . NATIONAL INSTRUMENTS. APPLICATION NOTES. Abstract. This application note discusses a technique known as beamforming for determining noise location of passing
GETTING STARTED GUIDE to ±10 V, 16 Bit, 250 …
www.ni.comMeasurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage.
NI 6509 User Guide and Specifications - National …
www.ni.comUSER GUIDE AND SPECIFICATIONS NI 6509 This document contains information about using the NI PCI-6509, NI PXI-6509, and NI PCIe-6509 data acquisition devices with the
NI 6528/6529 User Guide and Specifications - …
www.ni.comNI 6528/6529 User Guide and Specifications 6 ni.com Operate the DIO device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric
PXIe-5820 Getting Started Guide - National …
www.ni.comElectromagnetic Compatibility Guidelines This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications.
DEVICE SPECIFICATIONS NI 6722/6723
www.ni.comDEVICE SPECIFICATIONS NI 6722/6723 This document lists the specifications for the NI 6722/6723 analog output devices. The following specifications are typical at 25°C unless otherwise noted.
NI cRIO-9030 Specifications - National Instruments
www.ni.comSPECIFICATIONS NI cRIO-9030 Embedded CompactRIO Controller with Real-Time Processor and Reconfigurable FPGA This document lists the specifications for the National Instruments cRIO-9030.
NI PS-15 Power Supply User Manual and …
www.ni.com©National Instruments Corporation viii NI PS-15 Power Supply User Manual About This Manual The NI PS-15 Power Supply User Manual describes the features and specifications of the NI PS-15 power supply and contains information
NI cDAQ -9191
www.ni.comDigital output sample clock frequency Streaming from application memory System-dependent Regeneration from FIFO 0 MHz to 10 MHz Finite 0 MHz to 10 MHz
NI PXIe-1435 User Guide and Specifications - …
www.ni.comNI PXIe-1435 User Guide and Specifications The NI PXIe-1435 (NI 1435) is a PXI Express (PXIe) image acquisition device that supports Base, Medium, Full, and Extended Full configuration Camera Link cameras and supports Power over Camera
Related documents
S7-300 SM331;AI 8x12 Bit Getting Started Part 2: Voltage ...
cache.industry.siemens.com2 terminal block tpa,3-row for analog modules of the simatic s7;connection using flat round cable connections via spring clips 6es7924-0cc00-0ab0 2 shielding plate for analog terminal block 6es7928-1ba00-0aa0 4 connector (ribbon cable connector) as per din 41652, 16-pin, snap-on/screw-on 6es7921-3be10-0aa0
7800 SERIES Relay Module - Honeywell
customer.honeywell.com7800 SERIES EC7830A, EC7850A RELAY MODULE 3 65-0200—1 Table 1A. Terminal Ratings for EC7830A. Terminal No. Abbreviation Description Ratings G — Flame Sensor Ground 1 — Earth G — Earth Ground 1 — N — Line Voltage Common (Neutral) — 3 AL Alarm (Normally Open) 220/230/240 Vac, 1A, 10A inrush for 5000 cycles.
Field Effect Transistors - Learn About Electronics
learnabout-electronics.orgModule 4.2 How a JFET Works . The JFET is a Voltage Controlled Transistor. The JFET is a voltage controlled transistor that has two distinct areas of operation depending on the whether the voltage applied to the Source and Drain terminals is greater or less that the transistor's Pinch-Off Voltage . The Pinch Off Voltage
POINT I/O Common Terminal Module and Voltage …
literature.rockwellautomation.comPOINT I/O Common Terminal Module and Voltage Terminal Module 3 Publication 1734-IN024A-EN-E - March 2005 WARNING Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II
1794-IN050J-EN-P FLEX I/O Thermocouple/RTD Input Analog ...
literature.rockwellautomation.comgroove (6) on the terminal base. 5. Press firmly and evenly to seat the module in the terminal base unit. The module is seated when the latching mechanism (7) is locked into the module. Connect Wiring for the 1794-TB3G, 1794-TB3GK and 1794-TB3GS Terminal Base 1. Connect individual input wiring and associated signal returns
Phase-Adaptive Power Module SPEC (369835)
www.lutron.com• Each terminal accepts up to two 12 AWG (2.5 mm2) wires. Environment • 32 to 104 °F (0 to 40 °C). Relative humidity less than 90% non-condensing. • Indoor use only. • Maximum heat output of module: 135 BTU / hour. Mounting • Surface or recess mount. • Power module is UL tested and approved for use in
40ADC UPS Module DR-UPS40
www.meanwell.com40adc ups module dr-ups40 ’ = dc input / dc bus battery input / output others environment dr-ups40 dc voltage (typ.) note.5 rated current voltage range (typ.) current range charge current (typ.) note.4 external battery (typ.) relay contact rating (max.) dc bus ok battery fail note.2 battery discharge working temp. working humidity storage ...
High Voltage / High Current Connector Systems
www.tti.comPlanned terminal diameter families – 4-5 mm 80-100A – 6 mm 150A – 8.0 mm 200-250A – 11.0 mm 400A – Up to 14 mm 500A Molex confidential, all information in this presentation covered by NDA Example Hyperboloid terminal