TCN75S 2-Wire Serial Temperature Sensor Data Sheet
TCN75A DS21935D-page 4 2010 Microchip Technology Inc. Graphical Symbol Description DIGITAL INPUT/OUTPUT PIN CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, VDD = 2.7V to 5.5V, GND = Ground and TA = -40°C to +125°C. Parameters Sym Min Typ Max Units Conditions
Download TCN75S 2-Wire Serial Temperature Sensor Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
LM1949 Injector Drive Controller (Rev. C) - TI.com
www.ti.comLM1949 www.ti.com SNLS349C – FEB 1995– REVISED MARCH 2013 LM1949 Injector Drive Controller Check for Samples: LM1949 1FEATURES DESCRIPTION The LM1949 linear integrated circuit serves as an
IR Receiver Modules for Remote Control Systems - Vishay
www.vishay.comTSOP362.., TSOP364.. www.vishay.com Vishay Semiconductors Rev. 1.8, 24-Sep-2018 3 Document Number: 82568 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
Low Voltage Temperature Sensors Data Sheet …
www.analog.comLow Voltage Temperature Sensors Data Sheet TMP35/TMP36/TMP37 FEATURES Low voltage operation (2.7 V to 5.5 V) S Calibrated directly in °C . 10 mV/°C scale factor (20 mV/°C on
EPCQ-A Serial Configuration Device Datasheet
www.intel.com1.4. Pin Information. 1.4.1. Pin-Out Diagram for EPCQ4A, EPCQ16A and EPCQ32A Devices. Figure 2. AS x1 and AS x4 Pin-Out Diagrams for EPCQ4A, EPCQ16A, and EPCQ32A
MAX803 - Very Low Supply Current 3-Pin Microprocessor ...
www.onsemi.comMAX803 Series, NCP803 Series www.onsemi.com 5 TYPICAL OPERATING CHARACTERISTICS 75 50 25 0 −50 −25 0 25 50 125 TEMPERATURE (°C) Figure 9. Power−Down Reset Delay vs.
MAX809S - Very Low Supply Current 3-Pin Microprocessor ...
www.onsemi.comMAX809 Series, MAX810 Series www.onsemi.com 3 PIN DESCRIPTION Pin No. Symbol Description 1 GND Ground 2 RESET (MAX809) RESET output remains low while VCC is below the reset voltage threshold, and for a reset timeout period after VCC rises above reset threshold 2 RESET (MAX810) RESET output remains high while VCC is below the reset voltage threshold, and for a reset timeout