Transcription of Accessories Catalog - Eaton
1 Hose Cleaning SystemHose Support ClampsSleeves and ShieldsCoilsAccessories CatalogEATON Accessories Catalog E-HOAS-MC001-E December 20072 Table ofContentsAssembly InstructionsHose with Sleeve .. 3 AccessoriesHose Cleaning System and Insertion Gages .. 5 Hose Protectors .. 6 Hose Spacers and Looms .. 7 Support Clamps .. 8 Sleeving .. 10 Bundling Straps .. 12 Protective Coils, Sleeves & Clamps .. 14AQ Hose Accessories Selection Chart .. 18WH Hose Sleeves and Guards Selection Chart .. 29 EATONA ccessories Catalog E-HOAS-MC001-E December 20073 AssemblyInstructionsHose with SleeveStep 1 Follow the appropriateassembly instructionsthrough the assembly of oneend fitting. Insert one end fit-ting in 2 Cut coil length.
2 Coil shouldbe cut to overall assemblylength OA minus the sumof the overall length of eachend fitting. ( A dimension).Step 33a Steel Protective Coil SleeveThe hose and the coil shouldbe held straight. Taping orcapping the hose end canprevent frayed wire endsfrom snagging on the one end to the coil out-ward to form a slight tab toassist grasping. (Cut off orbend back when installationis complete.) Hold the tabwith the thumb of one handwhile twisting the coil clock-wise approximately one footback from the coil tab. Whenthe coil opens up sufficiently,slip the tab end to the coilover the hose. Move the coilonto the hose by pulling atthe tab end while pushingwith the other hand. Be care-ful not to exceed the resilien-cy of the coil by stretching ittoo Steel Protective Coil SpringSlide coil over 4 Proceed with assembly ofsecond end Protective CoilSleevePlastic Coil SleeveStep 1 Follow the appropriate hoseassembly instructionsthrough the assembly ofboth end fittings.
3 Insert endfitting in 2 Cut coil length. Coil shouldbe cut to overall assemblylength OA minus the sumof the overall length of eachend fitting. ( A dimension).Step 3 Wrap the coil on the No. 900564A1900(spring)(Refer to page 14)Part No. 900705 A2900 (sleeve)Steel Protective CoilSpringPart No. 900952(sleeve)(Refer to page 15) Eaton Accessories Catalog E-HOAS-MC001-E December 20074 AssemblyInstructionsHose with SleeveFiresleeveStep 1 Follow the appropriate hoseassembly instructionsthrough the assembly of oneend fitting. Cut firesleeve tosame length as firesleeve over cut endof hose. Note: If applyingsleeve over Teflon orstripped cover assemblies,wrap exposed wire withtape. Grasp sleeve and slip over the hose assemblyas 2 Skin sleeve back from cutend of hose enough toallow assembly of secondend fitting.
4 (2A)Then center sleeve so that itcompletely covers bothsockets. (2B)Step 3 Insert tail of band clamp intohand clamping 4 Position band clamp oversleeve as shown and thendraw tight with hand tool and cut freeend of band clamp. Repeaton other end of complete, bend protrud-ing tail of clamp over clampbuckle. Part (Refer to page 15)Assembly procedures1.) Measure the length ofbundling sleeve required andcut to ) Begin folding over thebottom portions of thesleeve ) Fold over one end of thehook & loop material andfasten to the bottom. Work your way up the entirelength of sleeve this ) Your hoses are nowsecure and SleevesPart No. FC676 A4900(Refer to page 10)EATONA ccessories Catalog E-HOAS-MC001-E December 20075 AccessoriesHose CleaningSystem andInsertion GagesPART NUMBERUSAGEFF90308-01 For use with all hoses that mate with -4 through -16 TTC, TTC12 fittings and Z-fittingsFF90308-02 For use with all hoses that mate with -20 through -32 TTC, TTC 12 fittings and Z-fittingsFF90308-03 For use with all hoses that mate with -12, -16, -20 Spiral TTC fittings and Z-fittingsHose Insertion GagesPart No.
5 FF90308 Hose Cleaning SystemHose Kit Part No. FT1355-01FT1355-02 FOR USE WITH ALL HOSES THATMATE WITH TTC, TTC12 AND SPIRALTTC FITTINGS, Z-FITTINGSI mprove hose assembly relia-bility with these easy to usealuminum gages that aredesigned to ensure properfitting depth during bottom the hose inthe appropriately markedcavity and scribe a mark onthe hose flush with the topsurface of the gage. Insertthe fitting until the back ofthe socket is aligned withscribe Jetcleaner hose clean-ing system offers a revolu-tionary solution for the inter-nal cleaning of bulk hose andfinished hose a low pressure air gun,the Jetcleaner system routesa foam projectile through thehose to thoroughly removedebris remaining from cut-ting, skiving and assemblyoperations.
6 Available in kitform or as individual compo-nents, the Jetcleaner hosecleaning system is the system of choice for hoseassembly includes:Jetcleaner pistol, Hose nozzles, 1/4" through 2" ID,Adapter ring, Bench stand,Aluminum case, Quick dis-connect couplingNote: Hose projectiles (P/N FT1355-3-size)not included in Includes Jetcleaner pistol,Hose nozzles, 1/4" through 1-1/4" ID, Adapter ring,Bench stand, Aluminumcase, Quick disconnect cou-pling , and Hose projectilesAlso available individually:Jetcleaner pistol FT1355-1-01 Hose nozzles FT1355-2-sizeHose projectiles FT1355-3-sizeCoupling nozzles FT1355-4-sizeCoupling projectiles FT1355-5-sizeAdapter ring FT1355-10-01 Carrying case FT1355-11-02 Bench stand FT1355-12-01 Eaton Accessories Catalog E-HOAS-MC001-E December 20076 AccessoriesHose ProtectorsMarket Applications: Farming Industrial Trucking Mining Construction Aviation Support Public Transportation Road Maintenance Waste Management Original Equip.
7 ProtectorsPART NUMBERDESCRIPTIONHP4*4" Hose ProtectorCase of 50HP6*6" Hose ProtectorCase of 50HP8*8" Hose ProtectorCase of 50 HPM*Mixed Hose ProtectorsCase of 60*Hose protectors available in black, orangeor Protection For: Hydraulic Hoses Battery Cables Wiring Harness Brake Systems Fuel Lines Air Lines Radiator Hoses Oil LinesFeatures: Extremely high wear factor Formulated to resist solvents, oils, grease,gasoline, etc. 3 grooves protect cableties and prevent slipping Operating temperaturerange is -40 to 430 F. Exceptionally cost effective Easy installation in minutes no need to remove hose Packed in easy to assem-ble, colorful, counter dis-play box Available in 3 sizes 4", 6" and 8" cable tiesincluded7 Eaton Accessories Catalog E-HOAS-MC001-E December 2007 AccessoriesHose Spacersand LoomsFeatures: Prevents hose abrasion atpoints of contact Helps keep hoses organized Prevents damage from unrestrained hoses Easy to install Available in 4 sizes 3 4", 1", 11 8", 13 8" Packed in colorful counter display boxes of 48 cable ties included Also available in mixedboxes of 48 (12 each size)or refill bags of 12 Hose SpacersFeatures.
8 Prevents hose abrasion atpoints of contact Keeps multiple hoses organized Simplifies hose routing Prevents damage from unrestrained hoses Easy to install Available in 4 sizes 3 4", 1", 11 8", 13 8" Packed in colorful counter display boxes of 48 Also available in mixedboxes of 48 (12 each size)or refill bags of 12 Hose LoomsPART NUMBERDESCRIPTIONHSM-48 Case of 48 mixedHose SpacersPART NUMBERDESCRIPTIONHLM-48 Case of 48 mixedHose Looms8 AccessoriesSupport ClampsAeroquip Part No. 900729 Support ClampCLAMPCLAMP CLAMPCLAMP DASH (IN.)DASH (IN.) light weight vinyl-coat-ed steel support clamps are designed to support hose where long runs clamp not only furnish-es a cleaner installation, butprevents damage, exposureand lining will withstand highambient hole dia: Clamp dashno.
9 01 thru 8, 18 thru 23 is .406; 9 thru 17, 24thru 31 is . Accessories Catalog E-HOAS-MC001-E December 2007 WeatherheadTypical Application: Hose support for long hoselengths. Also used to insureproper hose routing whereabrasion, moving parts orheat may : C1010 steel with1/32" thick black vinyl cushion. Plating: Zinc-plated dichro-mate Catalog E-HOAS-MC001-E December 20079 AccessoriesSupport ClampsHeavy Duty HoseSupport ClampsPart No. FF90311 CLAMP INSIDE DIAMETERCLAMP INSIDE DIAMETERPART NUMBER(MM)(IN.)PART NUMBER(MM)(IN.) heavy duty weld-based clamps are designedto securely hold hose inapplications subject toimpulsing, flexing and vibrat-ing conditions.
10 The clampshelp prevent abrasion andextend hose life throughproper routing. Clamps arerated to ambient tempera-ture of +250 Accessories Catalog E-HOAS-MC001-E December 200710 AccessoriesSleevingBenefits Increases productivity inassembly and reassemblyof hose bundles Reduces contamination ofhoses during bundle assembly Forces routing of hydrauliclines for safety and effi-ciency Reduces risk of hosebursts, resulting in greateroperator safety Reduces time spent onfield repairs Replaces inefficientbundling methods andline-damaging cable ties Eliminates cumbersomewinding of spiral formed products Reduces old sock syn-drome bunching at endof bundled lines Eliminates line contamina-tion during hose replace-mentMaterials 1050 Ballistic Nylon.
