FX3U-3A-ADP USER'S MANUAL - Mitsubishi Electric

1 JY997D35601F Side B. Side A JAPANESE. Side B ENGLISH. Applicable standards [5] Direct mounting hole:2 holes of ( ") (mounting screw: M4 screw) 5) Connect the 0. IN 10. 11. FX3U-3A-ADP units made in June, 2009 or later comply with the EC Directive (EMC Not used when connecting to FX3GC/FX 3UC Series PLC. special adapter Directive) and UL standards (UL, cUL). Further information can be found in the [6] POWER LED (green): ( ) to the main B FX3U-48M. following MANUAL . Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'. unit as shown on C.

2 S. FX. 3U R/E. - 8M. the right. -48M FX3U-4. ** - **. FX3S Series Hardware MANUAL ( MANUAL No. JY997D48301). 3U. FX. [7] Terminal block (European type): P. O. W. E. R. FX3U-3A-ADP FX3G Series Hardware MANUAL ( MANUAL No. JY997D46001). FX3GC Series Hardware MANUAL ( MANUAL No. JY997D45201). Connect the analog voltage/current signal, and 24 V DC power supply. 6) Slide back the special adapter 6). [8] Special adapter connector: slide lock ( ). N. FX3U Series Hardware MANUAL ( MANUAL No. JY997D50301). RU. USER'S MANUAL . OP. ST. FX3UC (D, DS, DSS) Series Hardware MANUAL ( MANUAL No.

3 JY997D50501) Used to connect this special adapter to PLC main unit or special adapter. of the main unit to FX3UC-32MT-LT-2 Hardware MANUAL ( MANUAL No. JY997D31601) [9] DIN rail mounting hook fix the special 5). 6). Regarding the standards that relate to the main unit, please refer to either the FX [10] Special adapter fixing hook adapter ( ). series product catalog or consult with your nearest Mitsubishi product provider. [11] Special adapter connector: MANUAL Number JY997D35601 5). Attention Used to connect communication or analog special adapters to the left side of the Revision F This product is designed for use in industrial applications.

4 3AD-ADP. Date January 2017 Caution for compliance with EC Directive The analog special adapters have been found to be compliant to the European 2. Installation 5) B. standards in the aforesaid MANUAL and directive. However, for the very best For installation/uninstallation details, refer to the respective PLC USER'S MANUAL performance from what are in fact delicate measuring and controlled output Hardware Edition. This MANUAL describes the part names, dimensions, mounting, and specifications Connection precautions device Mitsubishi Electric would like to make the following points.

5 Of the product. Before use, read this MANUAL and the manuals of all relevant Connect all the high-speed I/O special adapters before connecting other As analog devices are sensitive by nature, their use should be considered INSTALLATION. products fully to acquire proficiency in handling and operating the product. Make special adapters when they are used in combination. carefully. For users of proprietary cables (integral with sensors or actuators), PRECAUTIONS. sure to learn all the product information, safety information, and precautions. Do not connect a high-speed I/O special adapter on the left side of any these users should follow those manufacturers installation requirements.

6 Store this MANUAL in a safe place so that it can be taken out and read whenever Make sure to cut off all phases of the power supply externally before attempting special adapters other than other high-speed I/O special adapters. Mitsubishi Electric recommend that shielded cables should be used. If NO other necessary. Always forward it to the end user. installation or wiring work. EMC protection is provided, then users may experience temporary loss or Registration: Failure to do so may cause Electric shock or damage to the product. 3. Wiring accuracy between 10 % in very heavy industrial areas.

7 The company and product names described in this MANUAL are registered However, Mitsubishi Electric suggest that if adequate EMC precautions are trademarks or the trademarks of their respective companies. INSTALLATION WIRING. followed for the users complete control system, users should expect accuracy Effective January 2017 as specified in this MANUAL . PRECAUTIONS PRECAUTIONS. Specifications are subject to change without notice. Sensitive analog cable should not be laid in the same trunking or cable Use the product within the generic environment specifications described in PLC Make sure to cut off all phases of the power supply externally before 2009 Mitsubishi Electric Corporation conduit as high voltage cabling.

8 Where possible users should run analog main unit MANUAL (Hardware Edition). attempting installation or wiring work. cables separately. Never use the product in areas with excessive dust, oily smoke, conductive dusts, Failure to do so may cause Electric shock or damage to the product. Good cable shielding should be used. When terminating the shield at Earth Safety Precautions (Read these precautions before use.) - ensure that no earth loops are accidentally created. corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , or NO 2 ), flammable gas, vibration or impacts, or expose it to high temperature, condensation, or rain and wind.

9 WIRING. This MANUAL classifies the safety precautions into two categories: When reading analog values, EMC accuracy can be improved out by If the product is used in such conditions, Electric shock, fire, malfunctions, PRECAUTIONS. and . averaging the readings. This can be achieved either through functions on the deterioration or damage may occur. analog special adapters or through a users program. When drilling screw holes or wiring, make sure cutting or wire debris does When drilling screw holes or wiring, make sure cutting or wire debris does not Indicates that incorrect handling may cause hazardous 1.

10 Outline enter the ventilation slits. not enter the ventilation slits. conditions, resulting in death or severe injury. The FX3U-3A-ADP special adapter for analog input and output (hereinafter called Failure to do so may cause fire, equipment failures or malfunctions. Failure to do so may cause fire, equipment failures or malfunctions. 3A-ADP) is a special adapter that adds to add two analog input points and one analog Do not touch the conductive parts of the product directly. Make sure to observe the following precautions in order to prevent any Indicates that incorrect handling may cause hazardous output point.