MCP2200 Data Sheet - Microchip Technology
Jan 05, 2010 · 1.5 USB Transceiver The MCP2200 has a built-in, USB 2.0, full-speed transceiver internally connected to the USB module. The USB transceiver obtains power from the V USB pin, which is internally connected to the 3.3V regulator. The best electrical signal quality is obtained when VUSB is locally bypassed with a high quality ceramic capacitor.
Tags:
Transceiver, Mcp2200, Bus transceiver
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
Power, Factors, Correction, Power factor correction in power conversion, Conversion
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Data, Routines, Data encryption, Encryption, Data encryption routines for pic24 and, Pic24
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
Controller, Touch, Capacitive, Projected capacitive touch, Projected, Projected capacitive touch controller
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
Development, With, Board, Projected, Gui development board with projected, Gui development board with projected capacitance, Capacitance
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Guide, User, Energy, Module, Rn4020 bluetooth low energy module user s guide, Rn4020, Bluetooth
Related documents
CP2103 - Silicon Labs
www.silabs.comThe CP2103 is a highly-integrated USB-to-UART Bridge Controller providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2103 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, EEPROM, and asynchronous serial data bus (UART)
CP2104 - Silicon Labs
www.silabs.comThe CP2104 is a highly-integrated USB-to-UART Bridge Controller providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2104 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, one-time programmable ROM, and asynchronous
Setting up the TS-590S/SG for FT8 operations - KENWOOD
www.kenwood.com(USB cable with ferrite core would be recommended to prevent RF interference.) 4. Confirm the COM port number which is assigned to the transceiver. Refer to the virtual . COM port driver download page above for how to identify the port. 5. Once full reset the transceiver by pressing [A/B (A=B)] + Power ON in order to
cp2102rev1 0 - SparkFun Electronics
www.sparkfun.comThe Universal Serial Bus function co ntroller in the CP2102 is a USB 2.0 co mpliant full-speed device with integrated transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
Serial, Electronic, Universal, Transceiver, Universal serial bus, Sparkfun, Sparkfun electronics
USB-Link™ Installation and Setup Manual - NEXIQ
www.nexiq.comDec 20, 2011 · USB-Link and its documentation may not be sublicensed or transferred without the prior written consent of IDSC Holdings LLC. This manual, as well as the software it describes, is furnished under license and may only be used or copied in ... built-in Bluetooth® transceiver.
Manual, Installation, Setup, Transceiver, Installation and setup manual
USB to serial chip CH340 - SparkFun Electronics
cdn.sparkfun.comasynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More detail about USB convert to printer interface please referring to the second manual CH340DS2. In infrared mode, add infrared transceiver to CH340 can compose USB infrared adapter, realize SIR infrared communication. USB 2. Features
Alternate Mode for USB Type-C : Going Beyond USB
www.ti.comdata bus, USB 3.1 transceiver/receiver (TX/RX) pairs, configuration channel (CC) for cable attach detection, cable orientation detection, role detection and current-mode detection. One unused CC pin becomes the VCONN pin, which supplies the power to active cables or adaptors. The VBUS pin is used for the cable bus power and GND
USB Power Delivery and Type-C - STMicroelectronics
www.st.comUSB 2.0. Interface. Cable Ground. Cable Bus Power. Secondary Bus. Configuration Channel. Two pins on the USB Type-C receptacle, CC1 and CC2, are used in the discovery, configuration and management of connections across USB type-C cable. High Speed Data Path (RX for USB 3.1, or reconfigured in Alternate Mode) High Speed Data Path (TX for USB 3.1 ...