NI USB-6001 Specifications - National Instruments

1 SPECIFICATIONSNI USB-6001 Low-Cost DAQ USB DeviceThe following Specifications are typical at 25 C, unless otherwise noted. For moreinformation about the NI USB-6001 , refer to the NI USB-6001 /6002/6003 User Guideavailable at InputNumber of sample rate (aggregate)20 typeSuccessive FIFO2,047 sourcesSoftware, PFI 0, PFI range 10 voltage 10 VOvervoltage 30 20 impedance>1 G ..Input bias current 200 pAAbsolute at full scale6 over temperature,full scale26 , no missing dB (DC to 5 kHz)..Bandwidth300 kHzAnalog range 10 update rate5 kS/s simultaneous per channel, FIFO2,047 sourcesSoftware, PFI 0, PFI current drive 5 circuit current 11 rate3 V/ 2 | | NI USB-6001 SpecificationsAbsolute accuracy (no load).

2 Typical at full over temperature, full scale 34 , no missing 1 state0 glitch-7 V for 10 sTimebaseNote The following Specifications apply to the sampling accuracy for hardware-timed analog input and analog frequency80 accuracy 100 nsDigital I/O13 digital 08 14 21 < >Static digital digital 1 Static digital input/output, counter source ordigital triggerNI USB-6001 Specifications | National Instruments | < >Static digital 0 Static digital input/output, counter source ordigital controlEach channel individually programmable asinput or driver typeEach channel individually programmable asopen collector or active maximum voltage V to 5.

3 5 V with respect to D k to D stateInputDigital voltage range (powered on)0 to 5 voltage range (powered off)0 to voltage protection 20 V on two lines per port (maximum of fivelines for all ports) for up to 24 hoursCaution Do not leave a voltage above V connected on any DIO line forextended periods of time when the device is powered off. This may lead to long termreliability VMaximum input leakage 5 mADigital Output (Active Drive)..Maximum VOL (4 mA) VOL (1 mA) VOH (4 mA) VOH (1 mA) output current per line 4 mA4 | | NI USB-6001 SpecificationsDigital Output (Open Collector).

4 Maximum VOL (4 mA) VOL (1 mA) VNote Minimum VOH dependent on user-provided pull-up resistor and voltagesource. Recommended pull-up resistor is 1 k .Using a 1 k pull-up resistor and 5 V voltagesource:..Minimum output (sinking) current per line -4 pull-up voltage5 VMaximum leakage 5 of measurementsEdge counting, rising or directionCount sourcePFI 0 or PFI input frequency5 high pulse width100 low pulse width100 nsNI USB-6001 Specifications | National Instruments | 5+5 V Power voltage+5 V, 3%.

5 Maximum current150 protection200 circuit current50 protection 20 VBus specificationUSB Full bus speed12 Mb/sPhysical screw terminal connector plugs mm mm mm, ( in. in. in.)..With screw terminal connector plugs mm mm mm, ( in. in. in.)6 | | NI USB-6001 SpecificationsFigure 1. NI USB-6001 in( mm) in.( mm) in.( mm) in.( mm)AOAO++33 3377++2 2 2266++1 1 1155++0 0 screw terminal connector plugs 83 g ( oz)..With screw terminal connector plugs 105 g ( oz)I/O connectors: USB Micro-B receptacle, (1)16-position screw terminal to mm2 (16 to 28 AWG).

6 Torque for screw - N m ( - lb. in.)If you need to clean the module, wipe it with a dry (IEC 60068-2-1 andIEC 60068-2-2)..Operating0 to 45 to 85 CHumidity (IEC 60068-2-56)..Operating5 to 95% RH, to 90% RH, noncondensingNI USB-6001 Specifications | National Instruments | Degree (IEC 60664) altitude2,000 mIndoor use product meets the requirements of the following standards of safety for electricalequipment for measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA 61010-1 Note For UL and other safety certifications, refer to the product label or the OnlineProduct Certification CompatibilityThis product meets the requirements of the following EMC standards for sensitive electricalequipment for measurement, control, and laboratory use: EN 61326-1 (IEC 61326-1): Class A emissions.

7 Basic immunity EN 55011 (CISPR 11): Group 1, Class A emissions EN 55022 (CISPR 22): Class A emissions EN 55024 (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class A emissions AS/NZS CISPR 22: Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissionsNote In the United States (per FCC 47 CFR), Class A equipment is intended foruse in commercial, light-industrial, and heavy-industrial locations. In Europe,Canada, Australia, and New Zealand (per CISPR 11) Class A equipment is intendedfor use only in heavy-industrial Group 1 equipment (per CISPR 11)

8 Is any industrial, scientific, or medicalequipment that does not intentionally generate radio frequency energy for thetreatment of material or inspection/analysis For EMC declarations and certifications, and additional information, refer tothe Online Product Certification | | NI USB-6001 SpecificationsCE Compliance This product meets the essential requirements of applicable European Directives, as follows: 2006/95/EC; Low-Voltage Directive (safety) 2004/108/EC; Electromagnetic Compatibility Directive (EMC)Online Product CertificationTo obtain product certifications and the DoC for this product, visit , searchby model number or product line, and click the appropriate link in the Certification ManagementNI is committed to designing and manufacturing products in an environmentally responsiblemanner.

9 NI recognizes that eliminating certain hazardous substances from our products isbeneficial to the environment and to NI additional environmental information, refer to the Minimize Our Environmental Impactweb page at This page contains the environmental regulations anddirectives with which NI complies, as well as other environmental information not included inthis Electrical and Electronic Equipment (WEEE)EU Customers This symbol indicates that waste products should be disposed ofseparately from municipal household waste according toWEEE Directive 2002/96/EC of the European Parliament and the Council on wasteelectrical and electronic equipment (WEEE).

10 All products at the end of their lifecycle must be sent to a WEEE collection and recycling center. Proper WEEE disposal reduces environmental impact and the risk to human health due topotentially hazardous substances used in such equipment. Your cooperation inproper WEEE disposal will contribute to the effective usage of natural resources. Forinformation about the available collection and recycling scheme in a particularcountry, go to RoHS National Instruments (RoHS) National Instruments RoHS (For information about China RoHScompliance, go to )