Example: bankruptcy
OPAx837 Low-Power, Precision, 105-MHz, Voltage-Feedback …
4.096 v ads8860 16-bit sar 1 msps ref5040 lm7705 opa837 2.2 nf 3.3 v gnd gnd gnd gnd 0 v 3.8 v pd gain = 1.05 v/v 0 v 4.0 v + 5.0 v ± 0.23 v + 3.3 v 22 22
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
SimpleLink™ CC3120, CC3220 Wi-Fi ... - Texas …
www.ti.comUser User x x x x x x x x x x x x x x x x x x x x Application Servers Vendor IoT Devices Internet Introduction www.ti.com 4 SWRA509A–February 2017–Revised March 2017 Submit Documentation Feedback
1.8-V Micropower CMOS Operational Amplifier …
www.ti.com5 OPA2333-HT www.ti.com SBOS483I –JULY 2009–REVISED MAY 2015 Product Folder Links: OPA2333-HT Copyright © 2009–2015, Texas Instruments Incorporated Submit Documentation Feedback
TMS320C28x DSP/BIOS 5.x Application …
www.ti.comSPRU625L—August 2012 API Functional Overview 9 Submit Documentation Feedback www.ti.com Naming Conventions 1.2 Naming Conventions The format for a DSP/BIOS operation name is a 3- or 4-letter prefix for the module that contains the
LM136-2.5,LM236-2.5,LM336-2 - TI.com
www.ti.comLM136-2.5/LM236-2.5/LM336-2.5V Reference Diode General Description The LM136-2.5/LM236-2.5 and LM336-2.5 integrated cir-cuits are …
www.ti.com SNVS749F - Texas Instruments
www.ti.comLM136-2.5-N SNVS749F – MAY 1998– REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Temperature Drift Figure 13. …
MSP430x2xx Family User's Guide (Rev. J) - TI.com
www.ti.comMSP430x2xx Family User's Guide Literature Number: SLAU144J December 2004– Revised July 2013
LMC6482 CMOS Dual Rail-To-Rail Input and Output ...
www.ti.comLMC6482 www.ti.com SNOS674E –NOVEMBER 1997–REVISED APRIL 2015 5 Pin Configuration and Functions D, DGK and P Packages 8-Pin SOIC, VSSOP and PDIP (Top View) Pin Functions PIN TYPE DESCRIPTION NO.
OPAx354 250-MHz, Rail-to-Rail I/O, CMOS …
www.ti.comOPA354 IN +IN V OUT V+ V Product Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use …
Analog linearization of resistance temperature …
www.ti.com21 Analog Applications Journal Texas Instruments Incorporated 4Q 2011 www.ti.com/aaj High-Performance Analog Products …
WL18x7MOD WiLink™ 8 Dual-Band Industrial …
www.ti.comProduct Folder Order Now Technical Documents Tools & Software Support & Community Reference Design An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
Related documents
Voltage Feedback vs. Current Feedback Op Amps
www.ti.comFrequency Dependant Gain Model Voltage Feedback Vs Current Feedback Op Amps 5 4 Frequency Dependant Gain Model The open loop gain, a for VF or Zt for CF, is frequency dependant in real op …
Analog & Digital Electronics
www.iitg.ac.inBasic Feedback Topologies Depending on the input signal (voltage or current) to be amplified and form of the output (voltage or current), amplifiers can be
UC3842/3/4/5 Provides Low-Cost Current-Mode Control
www.ti.comTiming Resistance vs Frequency 0019-10 FREOUENCY - (Hz) 0019-11 Figure 10 U-100A CURRENT SENSING AND LIMITING The UC3842 current sense input is configured as shown in Figure 12. Current-to-voltage conversion is done exter-nally with ground-referenced resistor Rs. Under normal operation the peak voltage across Rs is controlled by the
AD797 (Rev. K)
www.analog.comRev. K Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no ... Low Noise Op Amps Voltage Noise 0.9 nV 1.1 nV 1.8 nV 2.8 nV 3.2 nV 3.8 nV ... Input Common-Mode Voltage Range vs. Supply Voltage 00846-005 V) 20 0 0 20 15 5 5 10 10 15 SUPPLY VOLTAGE (±V) –VOUT +VOUT
High Stability Isolated Error Amplifier Data Sheet ADuM3190
www.analog.comStability in isolated feedback applications 0.5% initial accuracy 1% accuracy over the full temperature range Compatible with Type II or Type III compensation networks Reference voltage: 1.225 V Compatible with DOSA Low power operation: <7 mA total Wide voltage supply range V DD1: 3 V to 20 V V DD2: 3 V to 20 V Bandwidth: 400 kHz
A Single-Supply Op-Amp Circuit Collection
mil.ufl.eduA single-supply circuit (right side of Figure 1) connects the op-amp power pins to a positive voltage and ground. The positive voltage is connected to V CC+, and ground is connected to V CC-or GND. A virtual ground, halfway between the positive supply voltage and ground, is the reference for the input and output voltages.
Digital to Analog Converter - gatech.edu
ume.gatech.eduOp-amps that can handle those currents are rare and expensive. 2. If R = 10 Ωand VRef = 10 V R1 = 21-1*(10 Ω) = 10 Ω I1 = VRef/R1 = 10V/10 Ω= 1 A This current is more than a typical op-amp can handle. R-2R Resistor Ladder DAC 2R Bit 3 Vout Bit 0 2R Vs 2R Bit 2 2R Bit 1 R +-RR R2R •Simplest type of DAC •Requires only two precision ...