Example: dental hygienist
SECTION DETAIL – PANEL WITH HORIZONTAL TRIM
• OSB or Plywood Sheathing • Pressure-Treated Wood Furring (Minimum 3/4" Nominal, 23/32" Actual Thickness) having specific gravity of 0.42 or greater • Shown with Panhead Screws into Furring These drawings are published as an information guide only. These CAD drawings are intended as templates to assist the designer. They do not contain
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Installation Guide - James Hardie Pros
www.jameshardiepros.com1 | English CUTTING CEMENT HARDIEBACKER® BOARD • Use a straight edge as a guide to score the board’s face and snap upward …
HardieTrim Boards Products Description - James …
www.jameshardiepros.comHardieTrim boards, /4! /4 HardieTrim 5/4, 4/4 boards that should get two ®
HardiePlank Lap Siding Product Description - …
www.jameshardiepros.comGeneral Product Information Tools for utting and Fastening General Installation Reuirements General Fastener Reuirements Finishing and aintenance
TR1509 HardieTrim HZ Installation ... - James Hardie …
www.jameshardiepros.comjoist 1 in. min. water resistive siding barrier flashing deck material ledger trim flashing FLASHING/CLEARANCE REQUIREMENTS NO-COVER vertical trim 1/4 in. min.
Fastening Tips for HardiePlank Lap Siding …
www.jameshardiepros.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
Evaluation Report ESR 2290 - James Hardie Pros
www.jameshardiepros.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
Evaluation Report ESR 1844 - Fiber Cement Products
www.jameshardiepros.comESR-1844 | Most Widely Accepted and Trusted Page 2 of 6 4.2 Installation: 4.2.1 General: 8The manufacturer’s published installation instructions and this report must be strictly adhered to and a copy of this report and the instructions must be available
HardiePlank Lap Siding - James Hardie Pros
www.jameshardiepros.comIMPORTANT: To prevent damage to the drip edge, extra care should be taken when removing planks from the pallet, while handling, and when installing with a lap gauge.
INSTALLATION INSTRUCTIONS - James Hardie Pros
www.jameshardiepros.comHardie. This document is intended for use by builders, cladding installers, and other contractors who may be involved with the installation of the Reveal Panel System. The Reveal PanelSystem by James Hardie provides a durable, expressed joint panel appearance for building facades offering versatility to architects and builders.
Exterior Wall Drainage Requirements - James Hardie Pros
www.jameshardiepros.coma 3/8 inch air gap (i.e. rainscreen) between flat-to-wall siding and the water-resistive barrier as a best practice. James Hardie recommends that you consult with your design professional if you have questions regarding exterior wall drainage on your single-family project. Individual buildings All exterior cladding products, including hard siding,
Related documents
Fastener Loads for Plywood – Screws
www.grabberman.comPlywood-and-Metal Connections Self-drilling, self-tapping screws are commonly used to attach plywood up to 1-1/8 in. thick to steel flanges up to 3/16 in. thick. However, since threads are usually provided on only a portion of the fastener shank, it is important to specify the appropriate fastener length for a given plywood thickness.
Schluter -DITRA-HEAT Installation Guide
resources.schluter.comlayer OSB or plywood floor interior dry or wet areas Limitations minimum 2" x 2" (50 mm x 50 mm) tile Requirements maximum spacing of joists, I-joists, or floor trusses is 24" (610 mm) o.c. double layer wood floor consisting of: • minimum subfloor thickness – 23/32", 3/4" nom. (19 mm) tongue-and-groove • minimum underlayment thickness –
Preparing Files for the Laser Cutter
www.art.udel.eduexample, say you wanted a 5″ square hole cut into a piece of 1/4″ plywood. It makes more sense to define a 5″ square path to cut around versus a 5″ filled square bitmap. Both will produce a 5″ square hole in the plywood, but engraving the ... Paths with a stroke (thickness)- If you want the artwork to be filled in or for line/text to ...
Ray Bar Stock Lead Thickness Conversion Chart
www.raybar.comstandard thickness mm equivalent 0.3969mm 0.7937mm 0.9922mm 1.1906mm 1.5875mm 1.9844mm 2.3812mm 3.1750mm 3.9687mm 4.7625mm 6.3500mm 9.5250mm 12.7000mm 19.0500mm 25.4000mm ... lead lined plywood, panels and components lead lined wood and metal doors - lead lined frames x-ray lead glass - x-ray safety glass - lead acrylic ...
Grades and Specifications - Burt Forest
burtforest.comindustrial plywood industry. PS 1-83 establishes requirements for producing, marketing and specifying construction and industrial plywood. With the exception of Plyron and some APA Performance Rated Panels, all of the other plywood grades described in this guide are produced under the provisions of U.S. Product Standard PS 1-83.
MARINE PLYWOOD DATA SHEET
www.picoplywood.comMarine Plywood must use an adhesive which has been proven to be highly resistant against different environments. Multi-Ply construction according to Bristish Standard (BS1088): Each face veneer shall be a minimum of 1.3mm and not thicker than 3.8mm Each core veneer shall be no thicker than 4.8mm TECHNICAL FEATURES Standard Unit Value
Span Ratings - Schmeling
schmeling.comForm No. TT-037A February 2007 Page 2 of 2 APA RATED SHEATHING APA RATED STURD-I-FLOOR Panel Span Rating Typical Panel Thickness (in.) Panel