Introduction • SPI Pin Functionality Features
1.3. Multi Slave Systems - SS Pin Functionality The Slave Select ( SS) pin plays a central role in the SPI configuration. Depending on the mode the part is running in and the configuration of this pin, it can be used to activate or deactivate the devices. The SS pin can be compared with a chip select pin which has some extra features.
Download Introduction • SPI Pin Functionality Features
Information
Domain:
Source:
Link to this page:
Documents from same domain
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Related documents
RGB to NTSC/PAL Encoder AD724 - Analog Devices
www.analog.comAD724–SPECIFICATIONS –2– REV. B (Unless otherwise noted, V S = +5, T A = +258C, using FSC synchronous clock.All loads are 150 V 6 5% at the IC pins. Outputs are measured at the 75 V reverse terminated load.) Parameter Conditions Min Typ Max Units
CM108 Headset Audio Controller DataSheet - QSL.net
www.qsl.netDate: Feb/13/2007 Version: 1.6 - 6 - 3. PIN DESCRIPTIONS 3.1 PIN ASSIGNMENT BY PIN NUMBER Pin # Signal Name Pin # Signal Name Pin # Signal Name Pin # Signal Name 1 SPDIFO 13 GPIO3 25 AO 37 REGV 2 DW 14 DVSS1 26 AI 38 MSEL 3 DR 15 GPIO4 27 AI 39 VOLUP 4 SK 16 SDIN 28 P 40 PDSW
UTMI+ Low Pin Interface (ULPI) Specification
www.sparkfun.comRoute int pin to data(3) during 6-pin Serial Mode. Explain VBUS thresholds. Add T&MT diagram and updated text. Add new section to explain how PHY is aborted by Link. Various clarifications. 1.0rc2 January 13, 2004 Add block diagram. Tighten interface timing. Modify suspend protocol to more closely resemble UTMI.
W5100 Datasheet v1 1 6 - SparkFun Electronics
www.sparkfun.com1.6 LED Signals Symbol Type Pin No Description LINKLED O 66 Link LED Active low in link state indicates a good status for 10/100M. It is always ON when the link is OK and it flashes while in a TX or RX state. SPDLED O 67 Link speed LED