LTC3721-1 - Push-Pull PWM Controller
REFLD Load Regulation Load on VREF = 100µA to 5mA 2 15 mV REFLN Line Regulation VCC = 6.5V to 9.5V 1 10 mV REFTV Total Variation Line, Load and Temperature 4.900 5.000 5.100 V REFSC Short-Circuit Current VREF Shorted to GND 18 30 45 mA Push-Pull Outputs DRVH(x) Output High Voltage IOUT(x) = –100mA 9.2 V DRVL(x) Output Low Voltage IOUT(x ...
Download LTC3721-1 - Push-Pull PWM Controller
Information
Domain:
Source:
Link to this page:
Documents from same domain
AD743 Ultralow Noise BiFET Op Amp Data Sheet …
www.analog.comREV. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its
MT-070: In-Amp Input RFI Protection - Analog …
www.analog.comRev.0, 10/08, WK Page 1 of 6 MT-070 TUTORIAL In-Amp Input RFI Protection . PROTECTING IN-AMPS AGAINST RFI . Real-world applications must deal with an ever increasing amount of radio frequency
LTC3108 - Ultralow Voltage Step-Up Converter and …
www.analog.comLTC3108 3108fc For more information www.linear.com/LTC3108 LDO
1.8 V Low Power CMOS Rail-to-Rail Input/Output …
www.analog.com1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier Data Sheet AD8515 Rev. E Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable.
Low Cost Micropower, Low Noise CMOS Rail-to …
www.analog.comLow Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers Data Sheet AD8613/AD8617/AD8619 Rev. H Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable.
Low Cost CMOS, High Speed, Rail-to-Rail Amplifiers
www.analog.comLow Cost CMOS, High Speed, Rail-to-Rail Amplifiers Data Sheet ADA4891-1/ADA4891-2/ADA4891-3/ADA4891-4 Rev. F Document Feedback Information furnished by Analog Devices ...
Zero-Drift, Single-Supply, Rail-to-Rail Input/Output ...
www.analog.comZero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifier Data Sheet AD8628/AD8629/AD8630 FEATURES Lowest auto-zero amplifier noise Low offset voltage: 1 µV AD8628
FEATURES DESCRIPTIO U - analog.com
www.analog.com1 LT1025 1025fb DESCRIPTIO U APPLICATIO S U 80µA Supply Current 4V to 36V Operation 0.5°C Initial Accuracy (A Version) Compatible with Standard Thermocouples (E, J, K, R, S, T) Auxiliary 10mV/°C Output Available in 8-Lead PDIP and SO Packages Thermocouple Cold Junction Compensator Centigrade Thermometer Temperature …
LT1173 - Micropower DC/DC Converter Adjustable …
www.analog.comLT1173 1 Micropower DC/DC Converter Adjustable and Fixed 5V, 12V VOUT 5V/DIV 0V PROGRAM 5V/DIV 5ms/DIV 1173 TA02 L1* 100µH LT1173 • TA01 + GND SW2 FB SW1 ILIM VIN 10 F LT1173
AD9850 CMOS, 125 MHz Complete DDS …
www.analog.comrev. h a cmos, 125 mhz complete dds synthesizer ad9850 functional block diagram clock out clock out analog in analog out dac rset …
Related documents
DESIGN OF HIGH PERFORMANCE CLASS B PUSH PULL …
ethesis.nitrkl.ac.inA push pull amplifier is an amplifier which has an output stage that can drive a current in either direction through the load. The output of a typical push pull amplifier consists of two identical BJTs or MOSFETs one sourcing current through the load while the other one sinking the current through the load.
Motor torque, load torque and selection of motors
www.electricalengineering-book.comMotor torque, load torque and selection of motors 2/43 2.1 Motor speed–torque curve Refer to Figure 2.1 where T st = starting torque or breakaway torque. T m = minimum, pull-in or pull-up torque. T po = pull-out, breakdown or maximum torque, obtainable over the entire speed range. In a good design this should occur as close to the rated slip ...
FRONT LOAD WASHER OWNER'S MANUAL MANUEL DE …
www.maytag.comLocate the Load & Go™ bulk dispenser. Gently pull up on the tab located on the bulk dispenser lid to lift the fill door. Fill to the “MAX” line (see illustrations at right) with HE liquid detergent or liquid fabric softener ™ Manual.
POSTGRES 10 WAYS TO LOAD DATA INTO
www.postgis.usUSING FOREIGN DATA WRAPPERS TO LOAD DATA file_fdw: use to read flat files and flat outputs. New in PostgreSQL 10 can read from commandline programs postgres_fdw: use to query other postgres servers ogr_fdw - use to query and load spatial formats and also other relational and flat (e.g. spreadsheets, odbc data sources, dbase files, openstreetmap ...
Forklift Safety -- Proper Load Handling
www.tdi.texas.govForklift Safety – Proper Load Handling To handle a load safely, a forklift operator must consider dangers ranging from improper load weights to blind spots and hazards on the ground. When lifting, moving, or lowering a load with a forklift, smooth operation is …
Basics of Load Switches (Rev. A) - TI.com
www.ti.com• Pull-down resistance (RPD) – This is the value of the pull-down resistor from VOUT to GND when the device is disabled. 2 Why Do You Need Load Switches This section will provide a general overview of some applications where using a load switch is beneficial. 2.1 Power Distribution Many systems have limited control of sub-systems power ...
I2C Bus Pull-Up Resistor Calculation
www.ti.compullup resistors pull the line high when it is not driven low by the open-drain interface. The value of the pullup resistor is an important design consideration for I2C systems as an incorrect value can lead to signal loss. In this article we show the simple equations for the pullup resistor calculation which the system