SMBus Quick Start Guide - NXP
• A slave is a device that receives or responds to a command. A system may not include a host. For example, a simple battery charging system is a hostless system. In an SMBus system, a device can be master only, slave only, or it may act as a slave most of the time, but in special instances it becomes a master. Table 3. Reserved SMBus addresses 1
Download SMBus Quick Start Guide - NXP
Information
Domain:
Source:
Link to this page:
Documents from same domain
AN10441 Level shifting techniques in I2C-bus design
www.nxp.comDocument information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with
AN3234: Washing Machine Three-Phase AC …
www.nxp.comWashing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...
1. General description - nxp.com
www.nxp.com1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical
PCA9570 Remote 4-bit general purpose outputs for 1 MHz …
www.nxp.com1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile
P82B96 Dual bidirectional bus buffer - nxp.com
www.nxp.com1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface
S32K144 EVB Quick Start Guide - NXP Semiconductors
www.nxp.comJ14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the
Three-Phase BLDC Motor Sensorless Control Using …
www.nxp.comThis document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.
AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com
www.nxp.comAN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit
DSP56156 16-Bit Digital Signal Processor - nxp.com
www.nxp.comThe DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-
SAA7706H Car radio Digital Signal Processor (DSP)
www.nxp.comCar radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
Related documents
Application Note Slave Controller - Beckhoff Automation
download.beckhoff.comSlave Controller – Application Note PHY Selection Guide 1 1 Overview An EtherCAT Slave Controller (ESC) takes care of the EtherCAT communication as an interface between the EtherCAT fieldbus (Ethernet) and the slave application. EtherCAT uses 100Mbit/s full duplex Ethernet communication. EtherCAT G uses 1,000Mbit/s full duplex
Interfacing to High Speed ADCs via SPI - Analog Devices
www.analog.comThis application note describes how to use the serial peripheral interface ( SPI) port on Analog Devices, Inc., high speed converters . In addition, this application note defines the electrical, timing, and procedural requirements for interfacing to these devices. The implementation is compatible with industry -standard SPI
MPC5121e Serial Peripheral Interface (SPI)
www.nxp.comThe purpose of this application note is to describe the serial peripheral interface bus controller (SPI) implemented on Freescale’s MPC5121e microcontroller. It describes how to config ure and use the programmable serial controller (PSC) and PSC centralized FIFO controller (FIFOC) in all supported SPI modes. 1.1 Objective
SSI Synchronous Serial Interface Master - Application Note
www.posital.comAPPLICATION NOTE 2013-11-08 6/26 Art.No. 10021488 1. SSI Theory Synchronous Serial Interface (SSI) is a widely used serial interface standard for industrial applications especially, rotary encoders. It is a point-to-point connection from a master (e.g. PLC, microcontroller or other control systems) to a slave (e.g. the rotary encoder).
AN4776 Application note - STMicroelectronics
www.st.comApplication note General-purpose timer cookbook for STM32 microcontrollers Introduction The timer peripheral is part of the essential set of peripherals embedded in all the STM32 microcontrollers. The number of timer peripherals and their respective features differ from ... The master/slave controller unit of the slave timer is configured to ...
SPI Configuration and Flash Programming in UltraScale ...
www.xilinx.comapplication note, SPI operates in a full duplex mode sending commands and addresses from the master over the master-output, slave-input (MOSI) line and receiving data over the master-input, slave-output (MISO) line. Data is synchronous with an SPI clock (SCLK) signal, and the slave device is selected via an SPI select (SS#) signal.