TDA8954 2 × 210 W class-D power amplifier - NXP

AN10441 Level shifting techniques in I2C-bus design

Document information AN10441 Level shifting techniques in I2C-bus design Rev. 01 — 18 June 2007 Application note Info Content Keywords I2C-bus, level shifting Abstract Logic level shifting may be required when interfacing legacy devices with

  Notes, Applications, Levels, Technique, Shifting, Application note, An10441 level shifting techniques in, An10441

AN3234: Washing Machine Three-Phase AC …

Washing Machine Three-Phase AC Induction Motor Drive, Rev. 0 Indirect Vector Control 4 Freescale Semiconductor If you are looking for more theory on the field ...

  Machine, Washing, Washing machine

1. General description - nxp.com

1. General description The TJA1044 is part of the Mantis family of high-speed CAN transceivers. It provides an interface between a Controller Area Network (CAN) protocol controller and the physical

  General, Descriptions, General description, General description nxp

PCA9570 Remote 4-bit general purpose outputs for 1 MHz …

1. General description The PCA9570 is a CMOS device that provides 4 bits of General Purpose parallel Output (GPO) expansion in low voltage processor and handheld battery powered mobile

  General, Purpose, Remote, Output, General purpose, Pca9570 remote 4 bit general purpose outputs for, Pca9570

P82B96 Dual bidirectional bus buffer - nxp.com

1. General description The P82B96 is a bipolar IC that creates a non-latching, bidirectional, logic interface between the normal I2C-bus and a range of other bus configurations.It can interface

S32K144 EVB Quick Start Guide - NXP Semiconductors

J14 SWD connector. 3 EXTERNAL USE S32K144 EVBFeatures: ... USB connector of the USB cable to micro-B port J7 on the S32K144EVB. ... Windows, Linux and Mac operating systems. Using the MSD Flash Programmer 1. Locate the .srec file of your project , file is under the

Three-Phase BLDC Motor Sensorless Control Using …

This document describes the design of a three-phase brushless DC motor (BLDC motor) drive based on Freescale’s MC56F8013 and MC56F8023 dedicated motor control device. Brushless DC motors are popular in a wide application area.

  Phases, Using, Control, Motor, Three, Sensorless, Brushless, Brushless dc, Three phase brushless dc, Motor sensorless control using

AN11443 BFU550XR ISM 433 MHz LNA design - nxp.com

AN11443 BFU550XR ISM 433 MHz LNA design Rev. 1 — 23 January 2014 Application note . Document information Info Content Keywords BFU520, BFU530, BFU550 series, ISM-band, 433MHz 866MHz Abstract This document describes an ISM Frequency LNA design on BFU5xxXR Starter kit

  433 mhz, 433mhz

DSP56156 16-Bit Digital Signal Processor - nxp.com

The DSP56156 is a general-purpose MPU-style Digital Signal Processor (DSP). On a single semi- conductor chip, the DSP56156 comprises a very efficient 16-bit digital signal processing core, pro-

  Processor, Processing, Signal, Digital, Digital signal processing, Digital signal processor

SAA7706H Car radio Digital Signal Processor (DSP)

Car radio Digital Signal Processor (DSP) SAA7706H This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in

  Processor, Radio, Signal, Digital, Car radio digital signal processor

AUTOMATIC STREET LIGHT CONTROL SYSTEM (MINOR …

resistance is low therefore voltage at the inverting input ( IE pin 2) is higher than the voltage at the ... The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. This is known as the biasing. ... more positive than its cathode lead by at least the LED's forward voltage drop, current ...

  Automatic, Light, Positive, Drop, Fixed, Tester, Automatic street light

Total Solids, Volatile Solids - University of Florida

Total Solids, Volatile Solids Total Solids (TS)= Dry matter content of substrate Inverse of moisture content one of the most variable parameters between substrates water Volatile Solids (VS)= Combustible proportion of TS, organic matter Non-volatile Solids (Ash)= Inorganic material (Minerals, salts), does not contribute to methane

−300 mA, Ultralow Noise, High PSRR, Low Dropout Linear ...

Fixed output voltage options: −0.5 V to −4.5 V Adjustable output from −0.5 V to −V IN + 0.5 V Low output noise: 4 μV rms from 100 Hz to 100 kHz Noise spectral density: 20 nV/√Hz, 10 kHz to 1 MHz Power supply rejection ratio (PSRR) at −300 mA load 75 dB typical at 10 kHz 62 dB typical at 100 kHz 40 dB typical at 1 MHz

  Fixed

LT3462 (Rev. A) - Analog Devices

the use of tiny, low cost and low height capacitors and inductors. The LT3462/LT3462A operate in a dual inductor inverting topology that filters both the input and output currents. Very low output voltage ripple approaching 1mVP‑P can be achieved when ceramic capacitors are used. Fixed fre ‑ quency switching ensures a clean output free from low

  Devices, Analog devices, Analog, Fixed

LM78XX, LM78XXA - 3-Terminal 1 A Positive Voltage Regulator

The LM78XX series of three-terminal positive regulators is available in the TO-220 package and with several fixed output voltages, making them useful in a wide range of applications. Each type employs internal current limiting, thermal shut-down, and safe operating area protection. If adequate heat sinking is provided, they can deliver over

  Positive, Fixed

LM2596 - 3.0 A, Step-Down Switching Regulator

1 Vin This pin is the positive input supply for the LM2596 step−down switching regulator. In order to minimize voltage transi-ents and to supply the switching currents needed by the regulator, a suitable input bypass capacitor must be present (Cin in Figure 1).

  Positive

SRV05-4 ESD Protection Diode Array - ON Semiconductor

to as low a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per the IEC61000−4−2 waveform. Since the IEC61000−4−2 was written as a pass/fail spec for larger systems such as cell phones or laptop computers it is not clearly defined in the spec how to specify a clamping ...

  Drop