Transition-mode PFC controller - STMicroelectronics
FET or IGBT drive which, combined with the other features, makes the device an excellent low-cost solu-tion for EN61000-3-2 compliant SMPS's up to 300W. ... Tj Junction Temperature Operating range -40 to 150 °C Tstg Storage Temperature -55 to …
Download Transition-mode PFC controller - STMicroelectronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low-power dual operational amplifier - st.com
www.st.comFebruary 2016 DocID2471 Rev 17 1/24 This is information on a product in full production. www.st.com LM2904, LM2904A Low-power dual operational amplifier
AN3128 Application note - st.com
www.st.comJune 2011 Doc ID 16918 Rev 5 1/105 AN3128 Application note STM32 embedded graphic objects/touchscreen library Introduction This library is a firmware package which contains a collection of routines, data structures,
AN4767 Application note - st.com
www.st.comDocID028380 Rev 2 7/16 AN4767 Dual bank use cases 15 With dual bank, all the manipulation with the other bank is just another task of the main program.
AN3155 Application note - st.com
www.st.comOctober 2016 DocID17066 Rev 7 1/37 1 AN3155 Application note USART protocol used in the STM32 bootloader Introduction This application note describes the USART protocol used in the STM32 microcontroller
USB Power Delivery and Type-C - st.com
www.st.comUSB Type -C Overview USB Power Delivery specification introduces USB Type-C receptacle, plug and cable; they provide a smaller, thinner and more robust alternative to existing USB interconnect.
Datasheet - L78 - Positive voltage regulator ICs - …
www.st.comTO- 2 2 0 TO-2 2 0 F P DPAK D² PAK Features • Output current up to 1.5 A • Output voltages of 5; 6; 8; 8.5; 9; 12; 15; 18; 24 V • Thermal overload protection
AN2867 Application note - st.com
www.st.comMay 2017 DocID15287 Rev 11 1/43 1 AN2867 Application note Oscillator design guide for STM8AF/AL/S and STM32 microcontrollers Introduction Many designers know oscillators based on Pierce-Gate topology (hereinafter referred to as
AN4776 Application note - st.com
www.st.comMay 2017 DocID028459 Rev 2 1/73 1 AN4776 Application note General-purpose timer cookbook Introduction The timer peripheral is part of …
120-volt, 100-watt, DMOS audio amplifier with mute …
www.st.comSeptember 2010 Doc ID 6744 Rev 8 1/21 21 TDA7293 120-volt, 100-watt, DMOS audio amplifier with mute and standby Features Multipower BCD technology Very high operating voltage range (±50 V)
Electronic transformer for a 12V halogen lamp - …
www.st.comAPPLICATION NOTE AN528/0999 1/4 ELECTRONIC TRANSFORMER FOR A 12V HALOGEN LAMP by P. Fichera, R. Scollo 1. INTRODUCTION Lighting that uses halogen lamps is commonly found
Related documents
BSS138 - N-Channel Logic Level Enhancement Mode Field ...
www.onsemi.comR JA is the sum of the junction−to−case and case−to−ambient thermal resistance where the case thermal reference is defined as the solder mounting surface of the drain pins. R JA is guaranteed by design while R JA is determined by the user’s board design. a) 350°C/W when mounted on a minimum pad. 2. Pulse Test: Pulse Width ≤ 300 s ...
ON Semiconductor Is Now
www.onsemi.comJunction Temperature Range TJ 125 °C Storage Temperature Range Tstg −65 to +150 °C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are
Bootstrap Circuitry Selection for Half Bridge Configurations
www.ti.comA bootstrap circuit is used in half-bridge configurations to supply bias to the high-side FET. Figure 1 shows the charging path of a bootstrap circuit in a simplified half-bridge configuration using UCC27710, TI's 620V half-bridge driver with interlock. When the low-side FET is on (high-side FET is off), the HS pin and the
How to Implement a MOSFET with a Gate Driver
www.egr.msu.eduNov 13, 2014 · Frequency, Junction. Introduction A MOSFET is an acronym for metal-oxide semiconductor field-effect transistor. It is a special type of field-effect transistor (FET) and is the key component in high frequency, high efficiency switching applications across the electronics industry. A MOSFET is a voltage controlled device.
SN74LVC1G3157 Single-Pole Double-Throw Analog Switch ...
www.ti.comTJ Junction temperature 150 °C Tstg Storage temperature –65 150 °C (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.2 ESD Ratings VALUE UNIT V(ESD) Electrostatic discharge
150V VIN and VOUT Synchronous 4-Switch Buck-Boost ...
www.analog.comLT 3779 4 For more information www.analog.com ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 15V, VRUN = 5V, VEXTVCC = 0V, VDRVSET = 0V, VVINOV = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS …
Lecture 13: Amplifier Noise Calculations
rfic.eecs.berkeley.eduFET Layout To reduce the gate resistance, a multi-finger layout approach is commonly adopted. As a bonus, the junction capacitance is reduced due to the junction sharing. A. M. Niknejad University of California, Berkeley EECS 142 Lecture 13 p. 10/20 – p
Band-bending - Iowa State University
tuttle.merc.iastate.eduIn the p-n junction and BJT, we saw that the semiconductor band edges were bent in the depletion layers. We used the depletion approximation and Poisson’s equation to relate the band-bending (barrier height) to the electric field to the depletion layer width. In the case of depletion, our treatment is reasonably accurate. However, we
EPC2019 – Enhancement Mode Power Transistor
epc-co.comeGaN® FET DATASHEET EPC2019 EPC – POWER CONVERSION TECHNOLOGY LEADER | EPC-CO.COM | ©2022 | | 4 Figure 12: Transient Thermal Response Curves Junction-to-Board t1, Rectangular Pulse Duration, seconds Duty Cycle: Notes: Duty Factor: D = t 1/t 2 Peak T J = P DM x Z θJB x R θJB + T B P DM t 1 t 2 0.5 0.1 0.05 0.02 0.01 Z Single Pulse θJB