Connecting the Units ENGLISH> - Pioneer Latin

1 Connecting the Units ENGLISH>. Note: When an external power amp is being used with This unit is for vehicles with a 12-volt battery and this system, be sure not to connect the blue/white CAUTION: negative grounding. Before installing it in a recre- lead to the amp's power terminal. Likewise, do not Pioneer does not recommend that you ational vehicle, truck, or bus, check the battery connect the blue/white lead to the power terminal install or service your display yourself. voltage. of the auto-antenna. Such connection could cause To avoid shorts in the electrical system, be sure to excessive current drain and malfunction. Installing or servicing the product may disconnect the battery cable before beginning To avoid short-circuiting, cover the disconnected MANUAL DE INSTALACI N. expose you to risk of electric shock or installation. lead with insulating tape. Especially, insulate the other hazards. Refer all installation and Refer to the owner's manual for details on unused speaker leads without fail.

2 There is a possi- INSTALLATION MANUAL. servicing of your display to authorized Connecting the power amp and other Units , then bility of short-circuiting if the leads are not insulat- Pioneer service personnel. make connections correctly. ed. Secure the wiring with cable clamps or adhesive To prevent incorrect connection, the input side of Secure all wiring with cable clamps or tape. To protect the wiring, wrap adhesive tape the IP-BUS connector is blue, and the output side electrical tape. Do not allow any bare around them where they lie against metal parts. is black. Connect the connectors of the same wiring to remain exposed. Route and secure all wiring so it cannot touch any colors correctly. This unit cannot be installed in a vehicle that AVH-P6550 DVD. moving parts, such as the gear shift, handbrake and Do not drill a hole into the engine com- seat rails. Do not route wiring in places that get does not have an ACC (accessory) position on partment to connect the yellow lead of hot, such as near the heater outlet.

3 If the insulation the ignition switch. (Fig. 1). the unit to the vehicle battery. Engine of the wiring melts or gets torn, there is a danger of vibration may eventually cause the insu- the wiring short-circuiting to the vehicle body. Don't pass the yellow lead through a hole into the ACC O O. lation to fail at the point where the wire F F. OF. N. OF. N. passes from the passenger compartment engine compartment to connect to the battery. This STAR. STAR. will damage the lead insulation and cause a very into the engine compartment. Take extra dangerous short. T T. care in securing the wire at this point. Do not shorten any leads. If you do, the protection circuit may fail to work when it should. It is extremely dangerous to allow the Never feed power to other equipment by cutting display lead to become wound around ACC position No ACC position the insulation of the power supply lead of the unit the steering column or gearshift. Be sure and tapping into the lead.

4 The current capacity of to install the display in such a way that it the lead will be exceeded, causing overheating. Fig. 1. will not obstruct driving. When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder. Make sure that wires will not interfere Since a unique BPTL circuit is employed, never The black lead is ground. Please ground this lead with moving parts of the vehicle, such as wire so the speaker leads are directly grounded or separately from the ground of high-current prod- the left and right speaker leads are common. ucts such as power amps. the gearshift, parking brake or seat slid- If you ground the products together and the ground ing mechanism. If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the con- becomes detached, there is a risk of damage to the nector. products or fire. Do not shorten any leads. If you do, the protection circuit may fail to work prop- Speakers connected to this unit must be high- erly.

5 Power types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers Cords for this product and those for other products with output and/or impedance values other than may be different colors even if they have the same those noted here may result in the speakers function. When Connecting this product to another catching fire, emitting smoke or becoming dam- product, refer to the supplied manuals of both This product conforms to new cord colors. aged. products and connect cords that have the same Los colores de los cables este producto se conforman When this product's source is switched ON, a con- function. trol signal is output through the blue/white lead. con un nuevo c digo de colores. Connect to an external power amp's system remote control or the car's Auto-antenna relay control ter- minal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal. Printed in Japan Impreso en Jap n <CRD3784-A> RD <KMMNF/03C00000>.

6 Connecting the Units <ENGLISH>. Connecting the power cord Antenna cable (supplied). When Connecting to separately sold power amp 15 cm 15 cm Subwoofer output or non fading output IP-BUS input (Blue) Hide-away unit (SUBWOOFER OUTPUT or 2m NON-FADING OUTPUT). Black 23 cm Power amp (sold separately). Multi-CD player (sold separately) Antenna jack Violet IP-BUS cable m Black This product 21 pin cable (supplied) Rear output 26 pin cable (supplied) (REAR OUTPUT) RCA cables Violet (sold separately). 15 cm Power amp (sold separately). Yellow/black Connection method This product If you use a cellular telephone, connect it via the Front output Audio Mute lead on the cellular telephone. If not, 1. Clamp the lead. 2. Clamp firmly with (FRONT OUTPUT). keep the Audio Mute lead free of any connections. needle-nosed pliers. Power amp (sold separately). 15 cm Note: Red The position of the parking brake switch depends Fuse resistor on the vehicle model. For details, consult the To electric terminal controlled by ignition switch (12 V DC) vehicle Owner's Manual or dealer.

7 ON/OFF. Light green Used to detect the ON/OFF status of the parking brake. Orange/white Fuse resistor Blue/white This lead must be connected to the power supply side of the parking System remote control To lighting switch terminal. To system control terminal of the power amp brake switch. or Auto-antenna relay control terminal Yellow Fuse holder (max. 300 mA 12 V DC). To terminal always supplied Left Right with power regardless of Power supply side Parking brake When you connect separately sold ignition switch position. switch multi-channel processor (DEQ-P7050) + +. to this unit, do not connect anything to the Front speaker Front speaker Ground side . speaker leads and system remote control (blue/white). Black (ground). To vehicle (metal) body. Note: Blue/white + +. To system control terminal of the power amp When you connect DEQ-P7050 to this unit, Rear speaker Rear speaker or Auto-antenna relay control terminal separately sold power amp must be connected.

8 White Gray to DEQ-P7050. (max. 300 mA 12 V DC). + +. Front speaker Front speaker With a 2 speaker system, do not connect anything Note: White/black Gray/black to the speaker leads that are not connected to speakers. + +. Left Right Change the initial setting of this product Subwoofer Subwoofer Green Violet When you connect separately sold multi-channel processor (refer to the Operation Manual).. + + (DEQ-P7050) to this unit, do not connect anything to the The subwoofer output of this unit is monaural. Rear speaker Rear speaker speaker leads and system remote control (blue/white). Perform these connections when using Green/black Violet/black the optional amplifier. Fig. 2 Fig. 3. Connecting the Units <ENGLISH>. When Connecting with a back-up camera When Connecting with a multi-channel processor When Connecting the external video component and the display When using this product with a back-up camera, automatic switching to video from a back- Hide-away unit up camera when the gear shift is moved to REVERSE (R) position is possible.

9 AV-BUS input (Blue). IP-BUS input (Blue) 40 cm Blue Hide-away unit Blue 15 cm RCA cables Black (sold separately). We recommend that you use IP-BUS cable (supplied with a camera which outputs multi-channel processor) This product To audio outputs mirror reversed images. External video RCA cable component (sold separately) 23 cm (sold separately). Subwoofer output Back up camera or non fading output To video output To video output (SUBWOOFER OUTPUT or RCA cables NON-FADING OUTPUT) (sold separately) To audio inputs Extension lead (supplied) RCA cable (supplied with Display with 10 cm 8m multi-channel processor) RCA input jacks Violet/white Fuse resistor To video input Of the two lead wires connected to the back Blue Optical cable (supplied with lamp, connect the one in which the voltage multi-channel processor). changes when the gear shift is in the REVERSE. Fig. 6. (R) position. This connection enables the unit to It is necessary to set to AV INPUT in SET UP when Connecting the external video com- sense whether the car is moving forwards or Multi-channel processor ponent.

10 Backwards. (DEQ-P7050). (sold separately). When using a display connected to rear video output This product's rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD. Connection method Black Blue IP-BUS cable 1. Clamp the lead. 2. Clamp firmly with WARNING: needle-nosed Multi-CD player NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while pliers. Black Blue (sold separately). Driving. NEVER connect rear audio output (REAR MONITOR OUT) to sold separately power amp. IP-BUS cable (supplied with TV tuner) Hide-away TV tuner Note: ( GEX-P6450 TVP). It is necessary to set to B-CAMERA in SETUP when (sold separately). Connecting the back-up camera. AV-BUS cable (supplied with TV tuner) Black Fig. 4 Fig. 5. Installation <ENGLISH>. Note: When mounting the hide-away unit, make sure none of the leads are trapped between the hide- DIN Front/Rear-mount DIN Rear-mount Screw Before finally installing the unit, connect the wiring temporarily, making sure it is all connected away unit and the surrounding metalwork or fit- This unit can be properly installed up properly, and the unit and the system work tings.