Integrated Motor Pump - Eaton

1 Integrated Motor PumpMP15, MP22, MP45, MP75 & MP9215 kW, 20 hp to 92 kW, 125 hpService DataVickers Pumps2 IntroductionThe Vickers Integrated Motor Pump is aunique combination of a conventionalAC induction Motor cooled with systemhydraulic oil and a Vickers hydraulicpump, either fixed vane pump orvariable piston type, housed in a specialsound reduction combination provides anexceptionally quiet and small pumpingpackage for any industrial applicationrequiring up to 125 horsepower (92kilowatts) of continuous hydraulic package comes completelyassembled, tested, and ready the hydraulic oil through themotor, bathing both the rotor and stator,makes it possible to obtain twice thenormal continuous output power fromthe Motor windings.

2 As a result, physicalsize reductions of 35% to 50%compared with conventional pumpingpackages are possible. Normaloperation of the Motor is not affected bycirculating oil through it, nor is thesystem s hydraulic oil generated within the electric motoris carried away by the hydraulic fluid anddissipated by the hydraulic coolingsystem. A Motor fan is not needed,which makes it practical to cover theentire assembly ( Motor and pump) witha compact, polyethylene soundreduction enclosure. This reduces thesound from the pump as well as themotor, resulting in a noise levelreduction that is unsurpassed in complete line of standard Vickerspumps can be fitted to the IntegratedMotor Pump including single fixed vanepumps, single variable piston pumps ,double vane pumps , double pistonpumps or mixed vane and CodeSecond Pump Code (if required)NOTE: Second pump code must bepreceded by a slash ( / ).

3 Example: P57C / V45N; or P57C/P57 COutlet Position (viewed from electric Motor end)A{ - 12 o clockB -3 o clockC - 9 o clockNote: On piston pump units the case drain willalways be at the 12 o clock Port ConnectionsF1{ - 4-bolt flange port, ISO 6162-Type 1 (inch)F2 - 4-bolt flange port, ISO 6162-Type 2 (metric)Design NumberSubject to change. Installationdimensions unaltered for designnumbers 20 through 29 Feature SuffixS5 -Non-flooded inletS22 -Wye (start) / Delta (run) Motor winding** -Contact Vickers representative for further information regarding S**34587691012111212 Model SeriesMP - Integrated Motor PumpMotor Power (sizes)}}

4 15 - 15 kW, 20 hp22 - 22 kW, 30 hp45 - 45 kW, 60 hp75 - 75 kW, 100 hp92 - 92 kW, 125 hpVoltageAY - 230V 60 HzB{ - 460V 60 HzC - 575V 60 HzD - 380V 50 Hz E -380V 60 HzF -400V 50 HzG - 220V 60 HzH - 500V 50 HzWinding Type1 - StandardTerminal Box Position(viewed from Motor end)R{ - Right sideL - Left sideHydraulic Pump TypeP - Variable pistonV - Vane345781191012 Pump Displacement (cm3/rev)Piston:20, 32, 40, 45, 57, 74, 98, 131 Single vane:18, 27, 36, 40, 45, 55, 67, 81, 97, 112, 121, 138, 162, 193 Double vane - shaft end:40, 45, 55, 67, 81, 97, 112, 121, 138, 162 Double vane - cover end:18, 27, 36, 40, 45, 55, 67 Example: P20V40V4018 NOTE: When ordering double vane pump,designate shaft and cover end Control TypeN -No control (vane pump only)Piston pumps with cm3/rev displacementsof 20, 32, 40, 45:C -Pressure compensator (20, 40 cm3/rev) -Range is 25-210 bar (350-3000 psi), standardfactory setting is 210 bar (3000 psi).}}

5 C -Pressure compensator (32, 45 cm3/rev) -Range is 25-138 bar (350-2000 psi), standardfactory setting is 138 bar (2000 psi).CM - Pressure compensator range is 25-70bar (350-1000 psi), standard factory setting is70 bar (1000 psi).CV - Pressure compensator with load sensing(20, 40 cm3/rev) - Range is 25-210 bar(350-3000 psi), standard factory setting is 210bar (3000 psi).CV - Pressure compensator with load sensing(32, 45 cm3/rev) - Range is 25-138 bar(350-2000 psi), standard factory setting is 140bar (2000 psi).Piston pumps with cm3/rev displacementsof 57, 74, 98, 131:C -Pressure compensator (20, 40 cm3/rev) -Range is 70-250 bar (1000-3600 psi), standardfactory setting is 250 bar (3600 psi).

6 CM - Pressure compensator range is 40-70bar (580-1000 psi), standard factory setting is70 bar (1000 psi).CV - Pressure compensator with loadsensing, range is 70-280 bar (1000-4060 psi),standard factory setting is 250 bar (3600 psi).{ Preferred optionY Only available on MP15 & MP22 1313415 & 22 kW Electric MotorHousing & Stator S/AMP15MP22 Standard Winding230 VAC-60Hz930551460 VAC-60Hz930551575 VAC-50Hz3001671380 VAC-50Hz3001723230 VAC-60Hz930544460 VAC-60Hz930544380 VAC-50Hz3001731400 VAC-50Hz3001909 Rotor, Shaft & Key S/AMP15MP22230 VAC-60Hz930555460 VAC-60Hz930555575 VAC-60Hz931023380 VAC-50Hz3001765230 VAC-60Hz930548460 VAC-60Hz930548575 VAC-60Hz931024 End Bell Inlet930530 Flooded932234 Non-Flooded930531 End Bell B face30112 Bearing (2 req d)}

7 924561 Eye Bolt924577 Eye Bolt Spacer930999 o-ring (2 req d)930678 Wave Washer930532 Mounting Foot (2 req d)Standard Winding575 VAC-50Hz930895 Wye Delta Winding400 VAC-50Hz3019138380 VAC-50Hz3001766400 VAC-50Hz3001907 Wye Delta Winding400 VAC-50Hz3019139473427 Screw (16 req d)torque to 25-30 Nm (18 - 22 lb. ft.)400 VAC-50Hz3019504400 VAC-50Hz3019307400 VAC-50Hz3019505400 VAC-50Hz3019308460 VAC-60Hz3019648460 VAC-60Hz3019642380 VAC-50Hz3019220220 VAC-60Hz3019547380 VAC-60Hz3019458460 VAC-60Hz3019649460 VAC-60Hz3019643380 VAC-50Hz3019221220 VAC-60Hz3019548380 VAC-60Hz3019459930682 Washer (4 req d)473429 Screw (4 req d)torque to 2,4-2,9 Nm ( - lb.)

8 Ft.)930680 Dampening Washer (4 req d)930681 Dampening Sleeve (4 req d) 3/8 930679 Dampening Spacer (4 req d)515 & 22 kW Electric Motor 473401 Screw (4 req d) torque 10-12 Nm (7 - 9 lb. ft.)Electrical FeedthruMP15MP22 Standard Winding230 VAC-60Hz930662460 VAC-60Hz930661575 VAC-60Hz930661380 VAC-50Hz930662 Wye Delta Winding400 VAC-50Hz3001904230 VAC-60Hz929395460 VAC-60Hz930662575 VAC-60Hz930661380 VAC-50Hz930662400 VAC-50Hz3001904930694 Shrink Tube296758 o-ring474270 Screw (4 req d)torque Nm (19 - 22 lb. ft.)930665 Adapter262412 o-ring380 VAC-60Hz3001904380 VAC-50Hz3001904460 VAC-60Hz3001904 3001902 Metric inserts (8 if req d)400 VAC-50Hz930662400 VAC-50Hz930662460 VAC-60Hz3001904220 VAC-60Hz3001905931009 Tie Strap (6 req d)MP 15/22 Non-Flooded Inlet End Bell932234 Non-Flooded Inlet Bell473403 Screw (4 req d)torque 10-12 Nm (7-9 )

9 932233 Cover Plate262418 O-ring615 & 22 kW Integrated Motor Pump - Single Pump930786 Single shroud930833 Double shroud929400 Sound AbsorbingMaterial932106 3/4 Sound Absorbing MaterialExternal OutletsSee Table BelowCase Drain**263497 o-ring**924581 Grommet**924585 Cap**924578 Long Connector930521 Screw (6 req d)929390 Cushion Strip930620 Clamp FlangeAX214709 Bolts (4 req d) torque 85-103 Nm(63-76 lb. ft.)Note: Use with allPVH & 35V pumps3001651 B-C AdapterKit (if req d) Motor OutletsCouplingsHosePump InletsPump ClampsBoltsO-ringsSee Table Below 473474 Pump Mtg.

10 Bolts (2 req d for B face,vane or piston 4 req d for C face pistonpump) torque to 85-103 Nm (63-76 lb. ft .)473500 Pump Mtg. Bolts (2 req d for C facevane pumps ) torque to 210-256 Nm (155-189 lb. ft.) Pump TypeOutlet PositionPart #PVQ20 & 3212 o clock9306443 o clock9306459 o clock930643 PVQ40 & 4512 o clock9306483 & 9 o clock930647 PVH5712 o clock9306323 & 9 o clock930631 PVH7412 o clock9306363 & 9 o clock930635 PVH9812 o clock9306403 & 9 o clock930639 Load Sense Line3001956 PVQ3001848 PVH573001846 PVH743001845 PVH983001856 Remote compensator line(for all PVQ s)3001859 Remote compensator line(for all PVH s)3019063 IC tapping plate kit for PVHPump mtg.