LT3092 (Rev. D) - Analog Devices

1 LT30921 Rev. DFor more information FeedbackTYPICAL APPLICATIONDESCRIPTION200mA 2-Terminal Programmable Current SourceThe LT 3092 is a programmable 2-terminal current source. It requires only two resistors to set an output current between and 200mA. A multitude of Analog techniques lend themselves to actively programming the output current. The LT3092 is stable without input and output capacitors, offering high DC and AC impedance. This feature allows operation in intrinsically safe applications. The SET pin features 1% initial accuracy and low tem-perature coefficient.

2 Current regulation is better than 10ppm/V from to LT3092 can operate in a 2-terminal current source configuration in series with signal lines. It is ideal for driv-ing sensors, remote supplies, and as a precision current limiter for local protection circuitry includes reverse-battery and reverse-current protection, current limiting and thermal limiting. The LT3092 is offered in the 8-lead TSOT-23, 3-lead SOT-223 and 8-lead 3mm 3mm DFN 2-Terminal Current SourceFEATURESAPPLICATIONSn Programmable 2-Terminal Current Sourcen Maximum Output Current: 200mA n Wide Input Voltage Range: to 40Vn Input/Output Capacitors Not Requiredn Resistor Ratio Sets Output Currentn Initial Set Pin Current Accuracy.

3 1%n Reverse-Voltage Protectionn Reverse-Current Protectionn < / V Line Regulation Typicaln Current Limit and Thermal Shutdown Protectionn Available in 8-Lead SOT-23, 3-Lead SOT-223 and 8-Lead 3mm 3mm DFN Packagesn AEC-Q100 Qualified for Automotive Applicationsn 2-Terminal Floating Current Sourcen GND Referred Current Sourcen Variable Current Sourcen In-Line Limitern Intrinsic Safety CircuitsSET Pin Current vs Temperature3092 TA01aINSETOUT+ LT309210 AROUTRSETVIN VOUT = TO 40 VISOURCE=10 A RSETROUTTEMPERATURE ( C) PIN CURRENT ( A) TA01bAll registered trademarks and trademarks are the property of their respective DFor more information CONFIGURATIONABSOLUTE MAXIMUM RATINGSIN Pin Voltage Relative to SET, OUT.

4 40 VSET Pin Current (Note 6) .. 15mASET Pin Voltage (Relative to OUT, Note 6) .. 10 VOutput Short-Circuit Duration ..Indefinite(Note 1) All Voltages Relative to VOUTTOP VIEWDD PACKAGE8-LEAD (3mm 3mm) PLASTIC DFNTJMAX = 125 C, JA = 28 C/W, JC = 10 C/WEXPOSED PAD (PIN 9) IS OUT, MUST BE SOLDERED TO OUT ON THE PCB. SEE THE APPLICATIONS INFORMATION VIEWTAB IS OUTINOUTSETST PACKAGE3-LEAD PLASTIC SOT-223 TJMAX = 125 C, JA = 24 C/W, JC = 15 C/WTAB IS OUT, MUST BE SOLDERED TO OUT ON THE PCB. SEE THE APPLICATIONS INFORMATION 1 OUT 2 OUT 3 OUT 48 IN7 IN6 NC5 SETTOP VIEWTS8 PACKAGE8-LEAD PLASTIC TSOT-23 TJMAX = 125 C, JA = 57 C/W, JC = 15 C/WOperating Junction Temperature Range (Notes 2, 8) E, I Grades.

5 40 C to 125 C MP Grade .. 55 C to 125 C Storage Temperature Range .. 65 C to 150 CLead Temperature (ST, TS8 Packages Only) Soldering, 10 sec ..300 C LT30923 Rev. DFor more information INFORMATIONLEAD FREE FINISHTAPE AND REELPART MARKING*PACKAGE DESCRIPTIONTEMPERATURE RANGELT3092 EDD#PBFLT3092 EDD#TRPBFLFJD8-Lead (3mm 3mm) Plastic DFN 40 C to 125 CLT3092 IDD#PBFLT3092 IDD#TRPBFLFJD8-Lead (3mm 3mm) Plastic DFN 40 C to 125 CLT3092 EST#PBFLT3092 EST#TRPBF30923-Lead Plastic SOT-223 40 C to 125 CLT3092 IST#PBFLT3092 IST#TRPBF30923-Lead Plastic SOT-223 40 C to 125 CLT3092 MPST#PBFLT3092 MPST#TRPBF3092MP3-Lead Plastic SOT-223 55 C to 125 CLT3092 ETS8#PBFLT3092 ETS8#TRPBFLTFJW8-Lead Plastic SOT-23 40 C to 125 CLT3092 ITS8#PBFLT3092 ITS8#TRPBFLTFJW8-Lead Plastic SOT-23 40 C to 125 CAUTOMOTIVE PRODUCTS** LT3092 EST#WPBFLT3092 EST#WTRPBF30923-Lead Plastic SOT-223 40 C to 125 CLT3092 IST#WPBFLT3092 IST#WTRPBF30923-Lead Plastic SOT-223 40 C

6 To 125 CContact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.**Versions of this part are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. These models are designated with a #W suffix. Only the automotive grade products shown are available for use in automotive applications.

7 Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these DFor more information CHARACTERISTICSNote 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and 2: Unless otherwise specified, all voltages are with respect to VOUT. The LT3092E is tested and specified under pulse load conditions such that TJ @ TA.

8 The LT3092E is 100% tested at TA = 25 C. Performance at 40 C and 125 C is assured by design, characterization, and correlation with statistical process controls. The LT3092I is guaranteed to meet all data sheet specifications over the full 40 C to 125 C operating junction temperature range. The LT3092MP is 100% tested and guaranteed over the 55 C to 125 C operating junction temperature 3: Minimum load current is equivalent to the quiescent current of the part. Since all quiescent and drive current is delivered to the output of the part, the minimum load current is the minimum current required to maintain Pin Current ISETVIN = 2V, ILOAD = 1mA 2V VIN 40V, 1mA ILOAD 200mA A AOffset Voltage (VOUT VSET) VOSVIN = 2V, ILOAD = 1mA VIN = 2V, ILOAD = 1mA l 2 42 4mV mVCurrent Regulation (Note 7)

9 ISET VOS ILOAD = 1mA to 200mA ILOAD = 1mA to 200mA l 2nA mVLine Regulation ISET VOS VIN = 2V to 40V, ILOAD = 1mA VIN = 2V to 40V, ILOAD = mV/VMinimum Load Current (Note 3)2V VIN 40Vl300500 ADropout Voltage (Note 4)ILOAD = 10mA ILOAD = 200mAl VCurrent LimitVIN = 5V, VSET = 0V, VOUT = Current RMS Output Noise (Note 5)10Hz f Rejectionf = 120Hz, VRIPPLE = , ILOAD = , CSET = F, COUT = F f = 10kHz f = 1 MHz90 75 20dB dB dBThermal Regulation ISET10ms W The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25 C.

10 (Note 2)Note 4: For the LT3092 , dropout is specified as the minimum input-to-output voltage differential required supplying a given output current. Note 5: Adding a small capacitor across the reference current resistor lowers output noise. Adding this capacitor bypasses the resistor shot noise and reference current noise (see the Applications Information section).Note 6: Diodes with series 1k resistors clamp the SET pin to the OUT pin. These diodes and resistors only carry current under transient 7: Current regulation is Kelvin-sensed at the 8: This IC includes overtemperature protection that protects the device during momentary overload conditions.