PXI-4130 Specifications - National Instruments

1 SPECIFICATIONSPXI-4130 20 V, 40 W PXI Source Measure UnitThese Specifications apply to the PXI-4130 with APS-4100 auxiliary power supply and to thePXI-4130 without auxiliary power 2 SMU Channel Specifications (Channel 1)..4 Voltage Programming Programming Measurement Measurement 1 Additional Channel Specifications (Channel 0).. 6 Programming 0 Additional and Measurement 7 Calibration 7 Accuracy specification Derating versus Load Sinking Power versus Ambient Temperature for Channel 8 Power and and 11CE Compliance .. 12 Online Product Specifications describe the performance of a model under stated operatingconditions and are covered by the model describe values that are relevant to the use of the model under stated operatingconditions but are not covered by the model warranty.

2 Typical Specifications describe the expected performance met by a majority of themodels. Nominal Specifications describe parameters and attributes that may be useful in are Warranted unless otherwise are valid under the following conditions unless otherwise noted. Ambient temperature1 of 23 C 5 C 30 minutes warm-up time niDCPower Samples to Average property orNIDCPOWER_ATTR_SAMPLES_TO_AVERAGE attribute set to 300 for optimal 50 Hzand 60 Hz rejectionDevice CapabilitiesChannelDC Voltage RangesIsolationDC Current Source and SinkRanges SMU Channel (1)-20 V to +20 V-6 V to +6 V60 VDC, CAT I200 A2 mA20 mA200 mA2 A2 Utility Channel (0)0 V to 6 VN/A1 A (6 W)1 The ambient temperature of a PXI system is defined as the temperature at the chassis fan inlet (airintake).2 Current input/output for channel 1 is limited to 2 W or 300 mA when operating under internalpower.

3 Continuous sinking power for channel 1 is limited to 10 W, subject to derating above30 C. Refer to the figure Maximum Sinking Power versus Ambient Temperature for Channel | | PXI-4130 SpecificationsFigure 1. Channel 0 Quadrant DiagramV+V 6 V6 V I I+1A 1 AChannel 0: 6W in Quadrant IQuadrant ISourceQuadrant IISinkQuadrant IVSinkQuadrant IIIS ourceFigure 2. Channel 1 Quadrant DiagramQuadrant ISourceQuadrant IISinkQuadrant IVSinkQuadrant IIIS ourceV+V 20 V20 V I I+2A200mA20mA2mA200 A 200 A 2mA 20mA 200mA 2 AChannel 1: 40W in Quadrants I and III, 10W in Quadrants II and IVPXI-4130 Specifications | National Instruments | 3 SMU Channel Specifications (Channel 1)Voltage Programming Accuracy/ResolutionRangeResolutionAccura cy (% of Output + Offset)1 Year 23 C 5 C 20 + mV 6 + mVCurrent Programming Accuracy/Resolution3 RangeResolutionAccuracy (% of Output + Offset)1 Year 23 C 5 C 200 A10 + A2 mA100 + 1 A20 mA1 + 10 A200 mA10 + 100 A2 A4100 + 1 mAVoltage Measurement Accuracy/ResolutionRangeResolutionAccura cy (% of Reading + Offset)

4 1 Year 23 C 5 C 20 + mV 6 + mV3 Minimum programmable current limit/level is 2% of currents 500 mA, refer to the additional derating information in the figure AccuracySpecification Derating versus Load | | PXI-4130 SpecificationsCurrent Measurement Accuracy/ResolutionRangeResolutionAccura cy (% of Reading + Offset)1 Year 23 C 5 C 200 + A2 mA10 + A20 + 2 A200 mA1 + 40 A2 A410 + 200 AChannel 1 Additional SpecificationsSettling time5500 s, typicalOutput capacitanceLow setting10 nF, typicalHigh F, typicalSlew V/ s, typicalTransient responseRecovers to < of voltage range within200 s after a change in load current from 10%to 90% of current range, typicalNormal Mode noise (Source only)15 mVp-p into resistive load <5 mV RMS20 Hz to 20 MHz bandwidth, typicalRemote senseUp to 1 V drop per lead using internal poweror 12 V auxiliary power supply.

5 Add 120 Vto accuracy specification per volt of lead regulationVoltage20 mV per amp of output load using of range per volt of output change5 Settled to 1%, 1 V step, 50% of current range at final value, output capacitance set to low, usingauxiliary power Specifications | National Instruments | 5 Line regulation (% of output + offset, per volt of change in auxiliary power input) + 1 + of rangeTemperature coefficient (Tempco) is 10% of accuracy specification per Channel Specifications (Channel 0)Programming Accuracy/Resolution6 Output FunctionRangeResolutionAccuracy (% of output + offset)1 Year 23 C 10 C Voltage+6 + 4 mVCurrent1 + 4 mAMeasurement Accuracy/ResolutionMeasurement TypeRangeResolutionAccuracy (% of reading + offset)1 Year 23 C 10 C Voltage+6 + 4 mVCurrent1 + 4 mAChannel 0 Additional SpecificationsSettling time<1 ms, 10% to 90% of range, measured withfull load, typicalOutput capacitance33 F, typicalTransient responseRecovers to < of voltage range within50 s after a change in load current from 50%to 100% of current range, typicalNormal Mode noise and ripple (sourceonly, voltage)< mV RMS, 20 Hz to 20 MHz bandwidth,typical6 Minimum programmable current limit/level is 2% of currents 500 mA, refer to the additional derating information in the figure AccuracySpecification Derating versus Load | | PXI-4130 SpecificationsLoad of range per amp of output of range per volt of output changeTemperature coefficient (Tempco)

6 Is 15% of accuracy specification per and Measurement Timing8 Maximum output update rate3000 Updates/s, nominalMaximum measurement rate (samples toaverage = 1)3 kS/s, nominalSingle point update latency600 s, typicalProtectionAuxiliary power input protectionOvervoltage> VDC shut-off; >20 VDC crowbar(fused)Overcurrent or reverse voltageFusedCalibration IntervalRecommended calibration interval1 year8 Does not include load dependent settling Specifications | National Instruments | 7 Accuracy specification Derating versus Current (A)Additional Error (%) 0 Channel 1 Maximum Sinking Power versus AmbientTemperature for Channel 10501015202530354045505560 Power (Watts)2015105 Ambient Temperature ( C) Physical CharacteristicsDimensions3U, one-slot PXI/cPCI cm cm cm( in. in. in.), nominalWeight312 g (11 oz), typical8 | | PXI-4130 SpecificationsUser-replaceable fusesChannel 0 (internally-socketed)1, Littelfuse (F A 125 V), characteristicAuxiliary power input (front panelmount)1, 5 20 mm glass fuse(T A L 250 V), characteristicNote NI recommends Littelfuse for Auxiliary Power Input panel connectorsOutput channelsMINI-COMBICON, mm (6 position),nominalAuxiliary power inputMINI-COMBICON, mm (2 position),nominalNote Front panel connectors can accept wire gauges from 16 AWG to 28 RequirementsPXI power requirement10 W at 5 V1 W at V6 W at 12 W at -12 V, typicalAuxiliary power source9 inputrequirements11 VDC to VDC5 A maxEnvironmentMaximum altitude2,000 m (at 25 C ambient temperature)Pollution Degree2 Indoor use.

7 Channel 1 Specifications | National Instruments | 9 Operating EnvironmentAmbient temperature range0 C to 55 C (Tested in accordance withIEC 60068-2-1 and IEC 60068-2-2.)Relative humidity range10% to 90%, noncondensing (Tested inaccordance with IEC 60068-2-56.)Storage EnvironmentAmbient temperature range-40 C to 70 C (Tested in accordancewith IEC 60068-2-1 and IEC 60068-2-2.)Relative humidity range5% to 95%, noncondensing (Tested inaccordance with IEC 60068-2-56.)Shock and VibrationOperational shock30 g peak, half-sine, 11 ms pulse (Tested inaccordance with IEC 60068-2-27. Test profiledeveloped in accordance withMIL-PRF-28800F.)Random vibrationOperating5 Hz to 500 Hz, grms (Tested in accordancewith IEC 60068-2-64.)Nonoperating5 Hz to 500 Hz, grms (Tested in accordancewith IEC 60068-2-64. Test profile exceeds therequirements of MIL-PRF-28800F, Class 3.)

8 Compliance and CertificationsCaution You can impair the protection provided by the PXI-4130 if you use it in amanner not described in this To ensure the specified EMC performance, operate this product only withshielded cables and | | PXI-4130 SpecificationsSafetyCaution Do not connect to signals or use for measurements within CAT II, III, VoltageChannel-to-earth ground, continuous60 VDC, CAT I10, verified by dielectricwithstand test, 5 sThis product is designed to meet the requirements of the following electrical equipment safetystandards for measurement, control, and laboratory use: IEC 61010-1, EN 61010-1 UL 61010-1, CSA No. 61010-1 Note For UL and other safety certifications, refer to the product label or the OnlineProduct Certification CompatibilityThis product meets the requirements of the following EMC standards for electrical equipmentfor measurement, control, and laboratory use: EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity EN 55011 (CISPR 11): Group 1, Class A emissions EN 55022 (CISPR 22): Class A emissions EN 55024 (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class A emissions AS/NZS CISPR 22: Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissionsNote In the United States (per FCC 47 CFR), Class A equipment is intended foruse in commercial, light-industrial, and heavy-industrial locations.

9 In Europe,Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intendedfor use only in heavy-industrial Group 1 equipment (per CISPR 11) is any industrial, scientific, or medicalequipment that does not intentionally generate radio frequency energy for thetreatment of material or inspection/analysis For EMC declarations, certifications, and additional information, refer to the Online Product Certification Categories CAT I and CAT O (Other) are equivalent. These test and measurementcircuits are not intended for direct connection to the MAINs building installations of MeasurementCategories CAT II, III, or CAT Specifications | National Instruments | 11CE Compliance This product meets the essential requirements of applicable European Directives, as follows: 2014/35/EU; Low-Voltage Directive (safety) 2014/30/EU; Electromagnetic Compatibility Directive (EMC)Online Product CertificationRefer to the product Declaration of Conformity (DoC) for additional regulatory complianceinformation.

10 To obtain product certifications and the DoC for this product, visit , search by model number or product line, and click the appropriate link in theCertification ManagementNI is committed to designing and manufacturing products in an environmentally responsiblemanner. NI recognizes that eliminating certain hazardous substances from our products isbeneficial to the environment and to NI additional environmental information, refer to the Minimize Our Environmental Impactweb page at This page contains the environmental regulations anddirectives with which NI complies, as well as other environmental information not included inthis Electrical and Electronic Equipment (WEEE)EU Customers At the end of the product life cycle, all NI products must bedisposed of according to local laws and regulations. For more information abouthow to recycle NI products in your region, visit RoHS National Instruments (RoHS) National Instruments RoHS (For information about China RoHScompliance, go to )Information is subject to change without notice.