UC3842B - High Performance Current Mode Controllers
Power Supply Rejection Ratio (VCC = 12 V to 25 V, Note 5) PSRR − 70 − − 70 − dB Input Bias Current IIB − −2.0 −10 − −2.0 −10 A Propagation Delay (Current Sense Input to Output) tPLH(In/Out) − 150 300 − 150 300 ns OUTPUT SECTION Output Voltage Low State (ISink = 20 mA) (ISink = 200 mA) UC284XB, UC384XB UC384XBV, UC2843D
Download UC3842B - High Performance Current Mode Controllers
Information
Domain:
Source:
Link to this page:
Documents from same domain
BCP56T1 - NPN Silicon Epitaxial Transistor
www.onsemi.com© Semiconductor Components Industries, LLC, 2016 March, 2018 − Rev. 14 1 Publication Order Number: BCP56T1/D BCP56 Series NPN Silicon Epitaxial Transistor These NPN Silicon Epitaxial transistors are designed for use in
AN1040/D Mounting Considerations For Power …
www.onsemi.comSemiconductor Components Industries, LLC, 2001 May, 2001 – Rev. 3 1 Publication Order Number: AN1040/D AN1040/D Mounting Considerations For Power Semiconductors
Corporate Fact Sheet - ON Semiconductor
www.onsemi.comCompany Profile ON Semiconductor (Nasdaq: ON) is driving energy efficient innovations, empowering customers to reduce global energy use. The company is a leading supplier of semiconductor-based
AND8231 - Circuit Configuration Options for TVS …
www.onsemi.comAND8231/D www.onsemi.com 2 Avalanche TVS Diodes Avalanche diodes are a good TVS device for applications that require power line surge immunity and ESD protection.
BCP53 Series PNP Silicon Epitaxial Transistors
www.onsemi.comBCP53 Series www.onsemi.com 3 TYPICAL CHARACTERISTICS Figure 1. Collector Emitter Saturation Voltage vs. Collector Current Figure 2. DC Current Gain vs. Collector
AND8299 - EMC Tests and PCB Guidelines for …
www.onsemi.comAND8299 - EMC Tests and PCB Guidelines for Automotive Linear Regulators
BSS138 N-Channel Logic Level Enhancement Mode …
www.onsemi.com2005 Semiconductor Components Industries, LLC. September-2017, Rev. 3 Publication Order Number: BSS138/D BSS138 N-Channel Logic Level Enhancement Mode Field Effect Transistor
TND310 ON Semiconductor Device Nomenclature
www.onsemi.comThis document contains the device nomenclature breakdown (also referred to as the part number decoder, product naming convention, or part naming convention) for …
LP2950 - 100 mA, Low Power Low Dropout Voltage …
www.onsemi.comLP2950, LP2951, NCV2951 www.onsemi.com Dropout Voltage V 0 in LP2950/LP2951 BIAS CURRENT (mA) I = 25°C V
2018 PHILIPPINES BENEFITS SUMMARY - ON …
www.onsemi.com2018 PHILIPPINES BENEFITS SUMMARY Employees are eligible for most benefits program on the first day of employment. Holidays: Ten (10) paid national regular holidays and Eight (8) national special holidays per year as provided
Related documents
Low Drop-Out (LDO) Linear Regulators: Design ...
site.ieee.org• PSR: Power Supply Rejection (or ripple rejection) is a measure of the ac coupling between the input supply voltage on the output voltage. • Power Efficiency; This is the ratio of the output load power consumption to input supply power. Linear regulators are not really efficient especially at
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp …
www.analog.comThe AD820 is a precision, low power FET input op amp that can operate from a single supply of 5 V to 36 V, or dual supplies of ±2.5 V to ±18 V. It has true single-supply capability, with an input voltage range extending below the negative rail, allowing the AD820 to accommodate input signals below ground in the single-supply mode.
AD827 High Speed, Low Power Dual Op Amp Data Sheet …
www.analog.commode rejection ratio is a minimum of 80 dB. Power supply rejection ratio is maintained at better than 20 dB with input frequencies as high as 1 MHz, thus minimizing noise feedthrough from switching power supplies. The AD827 is also ideal for use in demanding video applica-tions, driving coaxial cables with less than 0.04% differential
NCS2006 - 3 MHz, 125 uA Low Power Operational Amplifier
www.onsemi.comSUPPLY CHARACTERISTICS Power Supply Rejection Ratio PSRR No Load 67 90 dB 64 Power Supply Quiescent Current IDD Per channel, no load 125 170 A 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization.
Low-power dual operational amplifiers
www.st.comSupply voltage rejection ratio V CC + = 5 V to 30 V, R s dB T min ≤ T amb ≤ T max 65 I CC Supply current, all amp, no load T min ≤ T amb ≤ T max V CC + = 5 V 0.7 1.2 mA T min ≤ T amb ≤ T max V CC + = 30 V 2 CMR Common mode rejection ratio R s dB T min ≤ T amb ≤ T max 60 I source Output current source V CC + = 15 V, V o = 2 V, V ...
Datasheet - TDA2822D - Dual low voltage power amplifier
www.st.comSVR Supply voltage rejection f = 100 Hz 40 dB B Power bandwidth (-3 dB) RL = 8 kΩ, PO = 1 W 120 kHz TDA2822D Electrical characteristics DS0119 - Rev 3 page 7/12. Figure 5. Supply voltage rejection vs. frequency Figure 6. Output power vs. supply voltage (THD= 10%, f=1 kHz stereo) Figure 7. Total power dissipation vs. output power (bridge, RL=8 ...
Instrumentation Amplifier with Precision Voltage Reference ...
www.ti.comPower Supply Rejection (dB) Frequency (Hz) 1 10 100 1k 10k 100k 1M G = 4 G = 10 G = 500 G = 100 NEGATIVE POWER SUPPLY REJECTION vs FREQUENCY 120 100 80 60 40 20 0 Power Supply Rejection (dB) Frequency (Hz) S
Turbidity measurement - WHO
www.who.int• need power supply (mains or battery) • easily damaged ... than 5 NTU/JTU would be noticed by users and may cause rejection of the supply. • Where water is chlorinated, turbidity should be less than 5 NTU/JTU and preferably less than 1 NTU/JTU for chlorination to be effective.