3 A low drop positive voltage regulator: adjustable …

1 This is information on a product in full production. October 2013 DocID6738 Rev 271/2727LD10853 A low drop positive voltage regulator: adjustable and fixedDatasheet - production dataFeatures Typical dropout V (at 3 A) Three terminal adjustable or fixed output voltage V, V, V, 5 V Guaranteed output current up to 3 A Output tolerance 1% at 25 C and 2% in full temperature range Internal power and thermal limit Wide operating temperature range -40 C to 125 C Package available: TO-220, TO-220FP, D PAK, D PAK/A Pinout compatibility with standard adjustable VREGD escriptionThe LD1085 is a low drop voltage regulator able to provide up to 3 A of output current. Dropout is guaranteed at a maximum of V at the maximum output current, decreasing at lower loads. The LD1085 is pin-to-pin compatible with the older 3-terminal adjustable regulators, but offers better performance in terms of drop and output PNP regulators, where a part of the output current is wasted as quiescent current, the LD1085 quiescent current flows into the load, thus increase efficiency.

2 Only a 10 F minimum capacitor is need for device is supplied in TO-220, TO-220FP, D PAK and D PAK/A packages. On-chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1% at 25 PAKD Rev 27 Contents1 Diagram .. 32 Pin configuration .. 43 Maximum ratings .. 54 Application schematic .. 65 Electrical characteristics .. 76 Typical characteristics .. 127 Package mechanical data .. 168 Packaging mechanical data .. 239 Order codes .. 2610 Revision history .. 27 DocID6738 Rev 273/27LD1085 Diagram1 DiagramFigure 1. Schematic diagram Pin configurationLD10854/27 DocID6738 Rev 272 Pin configurationFigure 2. Pin connections (top view) TO-220 FPD PAK/ATO-220D PAKDocID6738 Rev 275/27LD1085 Maximum ratings3 Maximum ratingsNote:Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not impliedTable 1.

3 Absolute maximum ratingsSymbolParameterValueUnitVIDC input voltage30 VIOO utput currentInternally limitedmAPDP ower dissipationInternally limitedmWTSTGS torage temperature range-55 to +150 CTOPO perating junction temperature range-40 to +125 CTable 2. Thermal dataSymbolParameterTO-220TO-220 FPD PAK D PAK/AUnitRthJCThermal resistance junction-case353 C/WRthJAThermal resistance C/WApplication schematicLD10856/27 DocID6738 Rev 274 Application schematic Figure 3. Application circuit VOVREF1R2R1-------+ =DocID6738 Rev 277/27LD1085 Electrical characteristics5 Electrical characteristicsVI = V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 3. Electrical characteristics of LD1085#18 SymbolParameterTest voltage (1)IO = 0 mA, TJ = 25 = 0 to 3 A, VI = to 30 VOLine regulationIO = 0 mA, VI = to 18 V TJ = 25 = 0 mA, VI = to 15 VOLoad regulationIO = 0 to 3 A, TJ = 25 C210mVIO = 0 to 3 A 420mVVdDropout voltageIO = 3 A currentVI 30 V510mAIscShort-circuit currentVI - VO = 5 - VO = 25 regulationTA = 25 C, 30 ms voltage rejectionf = 120 Hz, CO = 25 F, IO = 3 A VI = 3 V6072dBeNRMS output noise voltage (% of VO)TA = 25 C, f =10 Hz to 10 term stabilityTA = 125 C, 1000 See short-circuit current curve for available output current at fixed characteristicsLD10858/27 DocID6738 Rev 27VI = V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified.

4 Table 4. Electrical characteristics of LD1085#25 SymbolParameterTest voltage (1)IO = 0 mA, TJ = 25 = 0 to 3 A, VI = to 30 VOLine regulationIO = 0 mA, VI = to 18 V, TJ = 25 = 0 mA, VI = to 18 VOLoad regulationIO = 0 to 3 A, TJ = 25 C210mVIO = 0 to 3 A 420mVVdDropout voltageIO = 3 A currentVI 30 V510mAIscShort-circuit currentVI - VO = 5 - VO = 25 regulationTA = 25 C, 30ms voltage rejectionf = 120 Hz, CO = 25 F, IO = 3 AVI = 3 V6072dBeNRMS output noise voltage (% of VO)TA = 25 C, f =10 Hz to 10 term stabilityTA = 125 C, 1000 See short-circuit current curve for available output current at fixed Rev 279/27LD1085 Electrical characteristicsVI = V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 5. Electrical characteristics of LD1085#33 SymbolParameterTest voltage (1)IO = 0 mA, TJ = 25 = 0 to 3 A, VI = to 30 VOLine regulationIO = 0 mA, VI = to 18 V, TJ = 25 = 0 mA, VI = to 18 V16mV VOLoad regulationIO = 0 to 3 A, TJ = 25 C315mVIO = 0 to 3 A720mVVdDropout voltageIO = 3 currentVI 30 V510mAIscShort-circuit currentVI - VO = 5 - VO = 25 regulationTA = 25 C, 30 ms voltage rejectionf = 120 Hz, CO = 25 F, IO = 3 AVI = 3 V6072dBeNRMS output noise voltage (% of VO)TA = 25 C, f =10 Hz to 10 term stabilityTA = 125 C, 1000 See short-circuit current curve for available output current at fixed characteristicsLD108510/27 DocID6738 Rev 27VI = 8 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified.

5 Table 6. Electrical characteristics of LD1085#50 SymbolParameterTest voltage (1)IO = 0 mA, TJ = 25 = 0 to 3 A, VI = to 30 VOLine regulationIO = 0 mA, VI = to 20 V, TJ = 25 = 0 mA, VI = to 20 V110mV VOLoad regulationIO = 0 to 3 A, TJ = 25 C510mVIO = 0 to 3 A1035mVVdDropout voltageIO = 3 currentVI 30 V510mAIscShort-circuit currentVI - VO = 5 - VO = 25 regulationTA = 25 C, 30 ms voltage rejectionf = 120 Hz, CO = 25 F, IO = 3 AVI = 10 3 V6072dBeNRMS output noise voltage (% of VO)TA = 25 C, f = 10 Hz to 10 term stabilityTA = 125 C, 1000 See short-circuit current curve for available output current at fixed Rev 2711/27LD1085 Electrical characteristicsVI = V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 7. Electrical characteristics of LD1085#SymbolParameterTest voltage (1)IO = 10 mA TJ = 25 = 10 mA to 3 A, VI = to 30 VOLine regulationIO = 10 mA, VI = to V,TJ = 25 = 10 mA, VI = to VOLoad regulationIO = 10 mA to 3 A, TJ = 25 = 0 to 3 voltageIO = 3 (min)Minimum load currentVI = 30 V310mAIscShort-circuit currentVI - VO = 5 - VO = 25 regulationTA = 25 C, 30ms voltage rejectionf = 120 Hz, CO = 25 F,CADJ = 25 F, IO = 3 A, VI = 3 V6072dBIADJA djust pin currentVI = V, IO = 10 mA55120 A IADJA djust pin current change (1)IO = 10 mA to 3 A, VI = to AeNRMS output noise voltage (% of VO)TA = 25 C, f =10 Hz to 10 term stabilityTA = 125 C, 1000 See short-circuit current curve for available output current at fixed characteristicsLD108512/27 DocID6738 Rev 276 Typical characteristicsUnless otherwise specified TJ = 25 C, CI = CO = 10 F.

6 Figure 4. Output voltage vs. temp. (IO = 3 A)Figure 5. Output voltage vs. temp. (IO = 0 mA) Figure 6. Output voltage vs. temp. (IO = 10 mA)Figure 7. Short-circuit current vs. dropout voltage DocID6738 Rev 2713/27LD1085 Typical characteristics Figure 8. Line regulation vs. temp. (IO = 10 mA)Figure 9. Load regulation vs. temperature Figure 10. Dropout voltage vs. temperatureFigure 11. Dropout voltage vs. output current Figure 12. Adjust pin current vs. temperatureFigure 13. Quiescent current vs. temperature Typical characteristicsLD108514/27 DocID6738 Rev 27 Figure 14. Line regulation vs. temperature(VIN = 15 V)Figure 15. Supply voltage rejection vs. output current Figure 16. Supply voltage rejection vs. frequencyFigure 17. Supply voltage rejection vs. temperature Figure 18. Minimum load current vs. temperatureFigure 19. Stability, VO = V DocID6738 Rev 2715/27LD1085 Typical characteristics Figure 20.

7 Stability, VO = 12 VFigure 21. Line transient VI=12 to 13V, IO=200mA, CI = 1 F(tant), CO=10 F(tant), CADJ=1 FFigure 22. Load transientFigure 23. Load transient (No CADJ) VI=12V, IO= to 3A, CI = 1 F(tant), CO=10 F(tant), CADJ=1 F VI=12V, IO= to 3A, CI = 1 F(tant), CO=10 F(tant), no CADJP ackage mechanical dataLD108516/27 DocID6738 Rev 277 Package mechanical dataIn order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST 8. TO-220 mechanical Rev 2717/27LD1085 Package mechanical dataFigure 24. TO-220 drawing BUHY'Package mechanical dataLD108518/27 DocID6738 Rev 27 Figure 25. TO-220FP drawingTable 9. TO-220FP mechanical Rev 2719/27LD1085 Package mechanical dataTable 10. D PAK mechanical 8 Package mechanical dataLD108520/27 DocID6738 Rev 27 Figure 26.

8 D PAK drawing0079457_TDocID6738 Rev 2721/27LD1085 Package mechanical dataTable 11. D PAK/A mechanical 8 Package mechanical dataLD108522/27 DocID6738 Rev 27 Figure 27. D PAK/A mechanical data7106164_EDocID6738 Rev 2723/27LD1085 Packaging mechanical data8 Packaging mechanical dataFigure 28. D PAK, D PAK/A footprint(a)Table 12. D PAK, D PAK/A tape and reel mechanical All dimensions are in mechanical dataLD108524/27 DocID6738 Rev 27 Figure 29. Tape for D PAK and D PAK/AFigure 30. Reel for D PAK and D PAK/AP1A0D1P0 FWEDB0K0 TUser direction of feedP210 pitches cumulativetolerance on tape +/- mmUser direction of feedRBending radiusB1 For machine ref. onlyincluding draft andradii concentric around B0AM08852v1 Top covertapeADBFull radiusG measured at hubCNREEL DIMENSIONS40mm holeAt sl ot locationTTape slot in core fortape start 25 mm Rev 2725/27LD1085 Order codes9 Order codes Table 13. Order codesPackagesOutput voltageTO-220TO-220 FPD PAKD PAK/A (T&R) VLD1085 VLD1085 PLD1085D2T-RLD1085D2M-RADJR evision historyLD108526/27 DocID6738 Rev 2710 Revision historyTable 14.

9 Document revision historyDateRevisionChanges07-Oct-200412 Mistake order codes - Table load regulation - V ==> V codes has been updated and new package DPAK, typo on VO test value in tables 3, 4 and codes codes : Table new order codes for Automotive grade products see Table 13 on page : Table 13 on page : Table 13 on page : Table 13 on page : Table 2 on page : Table 13 on page Modified Output voltage in voltage reference parameter Table 7 on page 11 and Table 8 on page 12. Minor text changes throughout the LD1085xx changed to the Features and the Description in cover Table1: Device summary, Table 9: Electrical characteristics of LD1085PY (Automotive Grade).Modified Figure 2: Pin connections (top view), Table 2: Thermal data, Tab l e 1 3: Order codes, Section 7: Package mechanical Section 8: Packaging mechanical text Rev 2727/27LD1085 Please Read Carefully:Information in this document is provided solely in connection with ST products.

10 STMicroelectronics NV and its subsidiaries ( ST ) reserve theright to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at anytime, without ST products are sold pursuant to ST s terms and conditions of are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes noliability whatsoever relating to the choice, selection or use of the ST products and services described license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of thisdocument refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party productsor services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of suchthird party products or services or any intellectual property contained OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWSOF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN.