HardieTrim Boards Products Description - James Hardie Pros
HardieTrim® Boards Products Description ... Special attention should be paid to the framing when using a sheathing that does not have fastener holding equivalent to OSB or Plywood sheathing. Step 1: Attach Flat Tabs to the back side of the trim with 4 18 ga. ½ in L x ¼ in W narrow crown corrosion resistant
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
Exterior Wall Drainage Requirements - James Hardie Pros
www.jameshardiepros.coma 3/8 inch air gap (i.e. rainscreen) between flat-to-wall siding and the water-resistive barrier as a best practice. James Hardie recommends that you consult with your design professional if you have questions regarding exterior wall drainage on your single-family project. Individual buildings All exterior cladding products, including hard siding,
Evaluation Report ESR 1844 - Fiber Cement Products
www.jameshardiepros.comESR-1844 | Most Widely Accepted and Trusted Page 2 of 6 4.2 Installation: 4.2.1 General: 8The manufacturer’s published installation instructions and this report must be strictly adhered to and a copy of this report and the instructions must be available
Installation Guide - James Hardie Pros
www.jameshardiepros.com1 | English CUTTING CEMENT HARDIEBACKER® BOARD • Use a straight edge as a guide to score the board’s face and snap upward …
HardiePlank Lap Siding Product Description - …
www.jameshardiepros.comGeneral Product Information Tools for utting and Fastening General Installation Reuirements General Fastener Reuirements Finishing and aintenance
Product, Descriptions, Siding, Lap siding product description
TR1509 HardieTrim HZ Installation ... - James Hardie …
www.jameshardiepros.comjoist 1 in. min. water resistive siding barrier flashing deck material ledger trim flashing FLASHING/CLEARANCE REQUIREMENTS NO-COVER vertical trim 1/4 in. min.
Fastening Tips for HardiePlank Lap Siding …
www.jameshardiepros.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
Tips, Fastening, Siding, Hardieplank, Fastening tips for hardieplank lap siding
Evaluation Report ESR 2290 - James Hardie Pros
www.jameshardiepros.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
HardiePlank Lap Siding - James Hardie Pros
www.jameshardiepros.comIMPORTANT: To prevent damage to the drip edge, extra care should be taken when removing planks from the pallet, while handling, and when installing with a lap gauge.
INSTALLATION INSTRUCTIONS - James Hardie Pros
www.jameshardiepros.comHardie. This document is intended for use by builders, cladding installers, and other contractors who may be involved with the installation of the Reveal Panel System. The Reveal PanelSystem by James Hardie provides a durable, expressed joint panel appearance for building facades offering versatility to architects and builders.
Installation Guide - James Hardie Pros
www.jameshardiepros.comFINISHING WITH TILE 1. Refer to ANSI A108 and the mortar and tile manufacturers’ published application guidelines for complete tiling instructions. 2. Wipe the surface of HardieBacker® cement board clean with a damp sponge just prior to adding mastic or mortar. 3. Spread the mastic or mortar with a notched trowel (Note: Please see “Materials
Related documents
Steel Framing Inspection Guide
www.steelframing.org• Recyclable – domestic CFS products have a minimum recycled content of 28% STEEL FRAMING COLD-FORMED S PARTS Cold-formed steel (CFS) studs and joists are hollow C-shaped sheet steel members that are used to frame walls, floors and roofs in residential and commercial structures. In residential designs that follow the prescriptive method
Truss-framed Construction - Forest Products Laboratory
www.fpl.fs.fed.usProducts Laboratory, Forest Service, USDA in Madison, Wisconsin, in response to the need for an economical, high-quality, and disaster-re sistant framing system. A public patent, No. 4,005,556 has been issued to Roger L. Tuomi on this system and it is available to anyone who wishes to make use of it. TFS evolved
CHAPTER 5: Design of Wood Framing - HUD USER
www.huduser.govChapter 5 - Design of Wood Framing 5.2.1 Lumber General As with all materials, the designer must consider wood’s strengths and weaknesses. A comprehensive source of technical information on wood characteristics is the Wood Engineering Handbook, Second Edition (Forest Products Laboratory, 1990). For the most part, the knowledge embodied in the
FRAMING AND CLOSING IN - Forest Products Laboratory
www.fpl.fs.fed.usFloor Framing Floor framing consists of columns or posts, beams, sill plates, joists, and subfloor. Assembled on a foundation, they form a level anchored platform for the rest of the house and a strong diaphragm to keep the lateral earth pressure from pushing in the top of the foundation wall. The columns or posts and beams of wood or steel that
VECTOR™ 50 DIRECT VENT LINEAR GAS APPLIANCE - Napoleon
www.napoleon.comBefore framing the appliance, ensure to install the fi restop fi rst. see-thru Before framing the appliance, ensure to install the fi restop fi rst as it will not fi t between the studs if installed after framing. * Minimum enclosure height maybe higher depending on venting confi guration (see minimum distance to combustibles). Ref LV50-2
North American Standard for Cold-Formed Steel Structural ...
cfsei.memberclicks.netiii AISI S240-15 This document is copyrighted by AISI. Any redistribution is prohibited. This first edition of AISI S240, North American Standard for -Formed Steel Structural FramingCold, is dedicated to John P. Matsen, P.E. John was a widely respected structural engineer for over