NCP380 - Fixed/Adjustable Current‐Limiting Power ...

1 DATA Semiconductor Components Industries, LLC, 2016 August, 2021 Rev. 191 Publication Order Number: NCP380 /DFixed/AdjustableCurrent LimitingPower DistributionSwitchesNCP380, NCV380 The NCP380 is a high side Power - distribution switch designed forapplications where heavy capacitive loads and short-circuits are likelyto be encountered. The device includes an integrated 55 mW (DFNpackage), P-channel MOSFET. The device limits the output current toa desired level by switching into a constant- current regulation modewhen the output load exceeds the current -limit threshold or a short ispresent. The current -limit threshold is either user adjustable between500 mA and A via an external resistor or internally fixed.

2 Thepower-switch rise and fall times are controlled to minimize currentringing during internal reverse-voltage detection comparator disables thepower-switch if the output voltage is higher than the input voltage toprotect devices on the input side of the FLAG logic output asserts low during over current ,reverse-voltage or over temperature conditions. The switch iscontrolled by a logic enable input active high or V V Operating Range 70 mW High-side MOSFET current Limit: User adjustable from 500 mA to A Fixed 500 mA, 1 A, A, 2 A and A Under Voltage Lock-out (UVLO) Built-in Soft-start Thermal Protection Soft Turn-off Reverse Voltage Protection Junction Temperature Range: 40 C to 125 C Enable Active High or Low (EN or EN) Compliance to IEC61000 4 2 (Level 4) kV (Contact) 15 kV (Air) UL Listed File No.

3 E343275 (NCP Versions Only) NCV Prefix for Automotive and Other Applications RequiringUnique Site and Control Change Requirements; AEC Q100 Qualified and PPAP Capable These are Pb-Free DevicesTypical Applications Laptops USB Ports/Hubs TVsUDFN6 CASE 517 ABMARKING DIAGRAMSXXMGG123654 TSOP 5 CASE 48315 XXXAYWGG(Note: Microdot may be in either location)TSOP 6 CASE 318 GXXX = Specific Device CodeA=Assembly LocationM= Date CodeY= YearW= Work WeekG= Pb Free PackageXXXAYWGG1 See detailed ordering and shipping information in the packagedimensions section on page 20 of this data INFORMATIONUDFN6 TSOP 5 TSOP 6 NCP380 , 1. Typical Application Circuit*For adjustable Version INPUT5 VFLAGENR fault100 kW1 mFFLAGENNCP380 OUTILIM*USBDATAUSBPortD+D VBUSGNDRlim120 mF(Top view)Figure 2.

4 Pin Connections123654 OUTILIM*FLAGINGNDENPAD1 UDFN6 OUTGNDFLAGINEN12354 TSOP 512364 OUTILIM*5 FLAGINGNDENTSOP 6*For adjustable version only, otherwise not 1. PIN FUNCTION DESCRIPTIONPin NameTypeDescriptionENINPUTE nable input, logic low/high ( EN or EN) turns on Power switchGNDPOWERG round connection;INPOWERP ower-switch input voltage; connect a 1 mF or greater ceramic capacitor from IN to GND as close as pos-sible to the open-drain output, asserted during overcurrent, overtemperature or reverse-voltage a 10 kW or greater resistor pull-up, otherwise leave output; connect a 1 mF ceramic capacitor from OUT to GND as close as possible to the ICis recommended.

5 A 1 mF or greater ceramic capacitor from OUT to GND must be connected if the USBrequirement ( mF capacitor minimum) is not *INPUTE xternal resistor used to set current -limit threshold; recommended 5 kW < RILIM < 250 **THERMALE xposed Thermal Pad: Must be soldered to PCB Ground plane*(For adjustable version only, otherwise not connected.**For DFN version , 2. MAXIMUM RATINGSR atingSymbolValueUnitFrom IN to OUT Pins: Input/Output (Note 1)VIN , VOUT to + , OUT, EN, ILIM, FLAG, Pins: Input/Output (Note 1)VEN, VILIM, VFLAG, VIN, VOUT to + Sink CurrentISINK1mAILIM Source CurrentILIM1mAESD Withstand Voltage (IEC 61000 4 2)(Output Only, when Bypassed with mF Capacitor Minimum)ESD IEC15 Air, 8 ContactkVHuman Body Model (HBM) ESD Rating (Note 2)ESD HBM2,000 VMachine Model (MM) ESD Rating (Notes 2 and 3)ESD MM200 VLatch-up Protection (Note 4)Pins IN, OUT, EN, ILIM, FLAGLU100mAMaximum Junction Temperature Range (Note 6)TJ 40 to +TSD CStorage Temperature RangeTSTG 40 to +150 CMoisture Sensitivity (Note 5)MSLL evel 1 Stresses exceeding those listed in the Maximum Ratings table may damage the device.)

6 If any of these limits are exceeded, device functionalityshould not be assumed, damage may occur and reliability may be According to JEDEC standard JESD22 This device series contains ESD protection and passes the following tests:Human Body Model (HBM) kV per JEDEC standard: JESD22 A114 for all Model (MM) 200 V per JEDEC standard: JESD22 A115 for all Except EN pin, 150 Latch up current Maximum Rating: 100 mA per JEDEC standard: JESD78 class Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: J STD A thermal shutdown protection avoids irreversible damage on the device due to Power 3. OPERATING CONDITIONSS ymbolParameterConditionsMinTypMaxUnitVIN O perational Power Voltage0 Temperature Range 4025+85 CTJJ unction Temperature Range 4025+125 CRILIMR esistor from ILIM to GND 250kWISINKFLAG Sink current Input mFCOUTD ecoupling Output CapacitorUSB Port per Hub120 mFRqJAThermal Resistance Junction-to-AirUDFN 6 Package (Notes 7 and 8) 120 C/WTSOP 5 Package (Notes 7 and 8) 305 C/WTSOP 6 Package (Notes 7 and 8) 280 C/WIOUTM aximum DC CurrentUDFN 6 Package 5, TSOP 6 Package Dissipation Rating (Note 9)

7 TA v 25 CUDFN 6 Package 830 mWTSOP 5 Package 325 mWTSOP 6 Package 350 mWTA = 85 CUDFN 6 Package 325 mWTSOP 5 Package 130 mWTSOP 6 Package 145 mW7. A thermal shutdown protection avoids irreversible damage on the device due to Power The RqJA is dependent of the PCB heat dissipation. Board used to drive this data was a 2 2 NCP380 EVB board. It is a 2 layers boardwith 2-once copper traces on top and bottom of the board. Exposed pad is connected to ground plane for UDFN 6 version The maximum Power dissipation (PD) is given by the following formula: PD+TJMAX*TARqJANCP380, 4. ELECTRICAL CHARACTERISTICS (Min & Max Limits apply for TA between 40 C to +85 C and TJ up to +125 C for VIN between V to V (Unless otherwise noted).)

8 Typical values are referenced to TA= +25 C and VIN=5V.)SymbolParameterConditionsMinTypM axUnitPOWER SWITCHRDS(on)Static Drain-source On-stateResistanceDFN PackageTSOP PackageVIN = 5 V 40 C < TJ < 125 C V < VIN < V 40 C < TJ < 125 C 110 VIN = 5 V 40 C < TJ < 125 C V < VIN < V 40 C < TJ < 125 C 135 TROutput Rise TimeVIN = 5 VCLOAD = 1 mF,RLOAD = 100 W (Note 10) = Fall TimeVIN = 5 = INPUT EN OR ENVIHHigh-level Input VVILLow-level Input Voltage CurrentVEN = 0 V, VEN = 5 V On TimeCLOAD = 1 mF, RLOAD = 100 W (Note 11) Off LIMITIOCPC urrent-limit Threshold(Maximum DC Output CurrentIOUT Delivered to Load)VIN = 5 VRILIM = 20 kW (Note 11)

9 = 40 kW(Notes 11 and 13) A (Note 12) A (Note 12) A (Note 12) A (Note 12) A (Note 12) Time to Short CircuitVIN = 5 V msTREGR egulation Protection Time142026msREVERSE-VOLTAGE PROTECTIONVREVR everse-voltage ComparatorTrip Point (VOUT VIN) 100 mVTREVTime from Reverse-voltageCondition to MOSFET Switch Off& FLAG LowVIN = 5 LOCKOUTVUVLOIN Pin Low-level Input VoltageVIN Pin HysteresisTJ = 25 C25 60mVTRUVLORe-arming CURRENTIINOFFLow-level Output Supply CurrentVIN = 5 V, No Load on OUT, Device OFFVEN = 0 V or VEN = 5 V Output SupplyCurrentVIN = 5 V, Device Enable2 A and A Versions1 A and A current A current Version 908070mAIREVR everse Leakage CurrentVOUT = 5 V, VIN = 0 VTJ = 25 C , 4.

10 ELECTRICAL CHARACTERISTICS (continued)(Min & Max Limits apply for TA between 40 C to +85 C and TJ up to +125 C for VIN between V to V (Unless otherwise noted).Typical values are referenced to TA= +25 C and VIN=5V.)SymbolUnitMaxTypMinConditionsPar ameterFLAG PINVOLFLAG Output Low VoltageIFLAG = 1 mA400mVILEAKOff-state LeakageVFLAG = 5 DeglitchFLAG De-assertion Time due to Overcurrent orReverse Voltage DeglitchFLAG Assertion due to SHUTDOWNTSDT hermal Shutdown Threshold140 CTSDOCPT hermal Regulation Threshold125 CTRSDT hermal Shutdown RearmingThreshold115 CProduct parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted.