NCP380 - Fixed/Adjustable Current‐Limiting Power ...
power-switch if the output voltage is higher than the input voltage to protect devices on the input side of the switch. The FLAG logic output asserts low during over current, reverse-voltage or over temperature conditions. The switch is controlled by a logic enable input active high or low. Features • 2.5 V – 5.5 V Operating Range
Download NCP380 - Fixed/Adjustable Current‐Limiting Power ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
BCP56T1 - NPN Silicon Epitaxial Transistor
www.onsemi.com© Semiconductor Components Industries, LLC, 2016 March, 2018 − Rev. 14 1 Publication Order Number: BCP56T1/D BCP56 Series NPN Silicon Epitaxial Transistor These NPN Silicon Epitaxial transistors are designed for use in
AN1040/D Mounting Considerations For Power …
www.onsemi.comSemiconductor Components Industries, LLC, 2001 May, 2001 – Rev. 3 1 Publication Order Number: AN1040/D AN1040/D Mounting Considerations For Power Semiconductors
Corporate Fact Sheet - ON Semiconductor
www.onsemi.comCompany Profile ON Semiconductor (Nasdaq: ON) is driving energy efficient innovations, empowering customers to reduce global energy use. The company is a leading supplier of semiconductor-based
AND8231 - Circuit Configuration Options for TVS …
www.onsemi.comAND8231/D www.onsemi.com 2 Avalanche TVS Diodes Avalanche diodes are a good TVS device for applications that require power line surge immunity and ESD protection.
BCP53 Series PNP Silicon Epitaxial Transistors
www.onsemi.comBCP53 Series www.onsemi.com 3 TYPICAL CHARACTERISTICS Figure 1. Collector Emitter Saturation Voltage vs. Collector Current Figure 2. DC Current Gain vs. Collector
AND8299 - EMC Tests and PCB Guidelines for …
www.onsemi.comAND8299 - EMC Tests and PCB Guidelines for Automotive Linear Regulators
BSS138 N-Channel Logic Level Enhancement Mode …
www.onsemi.com2005 Semiconductor Components Industries, LLC. September-2017, Rev. 3 Publication Order Number: BSS138/D BSS138 N-Channel Logic Level Enhancement Mode Field Effect Transistor
TND310 ON Semiconductor Device Nomenclature
www.onsemi.comThis document contains the device nomenclature breakdown (also referred to as the part number decoder, product naming convention, or part naming convention) for …
LP2950 - 100 mA, Low Power Low Dropout Voltage …
www.onsemi.comLP2950, LP2951, NCV2951 www.onsemi.com Dropout Voltage V 0 in LP2950/LP2951 BIAS CURRENT (mA) I = 25°C V
2018 PHILIPPINES BENEFITS SUMMARY - ON …
www.onsemi.com2018 PHILIPPINES BENEFITS SUMMARY Employees are eligible for most benefits program on the first day of employment. Holidays: Ten (10) paid national regular holidays and Eight (8) national special holidays per year as provided
Related documents
UNDERSTANDING RELAYS - Autoshop 101
autoshop101.comRelays are remote control electrical switches that are controlled by another switch, such as a horn switch or a computer as in a power train control module. Relays allow a small current flow circuit to control a higher current circuit. Several designs of relays are in use today, 3-pin, 4-pin, 5-pin, and 6-pin, single switch or dual switches.
Fundamentals of motor control - STMicroelectronics
www.st.comWhen the low side switch is ON, the load’s current flows through the resistor positioned in-between the low side and the ground ... • The motor is controlled applying a voltage on the motor leads. The higher the voltage, the higher the speed. The direction is changed reversing the polarity on the leads.
DIRECTV Universal Remote Control User’s Guide
www.att.comswitch under AV1, AV2 or TV to select the compo-nent you want to control. A green LED under the switch position will con-firm the component being controlled. Press TV INPUTto select the available inputs on your TV. (Note: Additional program-ming is required to activate the TV INPUT key. See instructions on page 11).
RadioRA 2 Maestro Local Controls SPEC (369225)
www.lutron.com4 Power Boosters / Load Interfaces: -6ND, -10ND, -6NA can be used to control power boosters / load interfaces. For a list of compatible power boosters / load interfaces see Compatible Power Boosters and Load Interfaces, page 11. 5 Minimum load depends on lamp and is not limited to a particular wattage. Refer to the LED Product Selection Tool at
Cisco SRW224P 24-Port 10/100 + 2-Port Gigabit Switch ...
www.cisco.comThe Cisco ® SRW224P 24-Port 10/100 + 2-Port Gigabit Switch (Figure 1) offers a highly secure way to expand your network. Web-based configuration of the switch is secured using SSL. User access is verified using 802.1X security with a RADIUS authentication mechanism and can also be controlled using MAC-based filtering.
H-Bridge Gate Driver IC - NXP
www.nxp.comgate driver channels are independently controlled by four separate input pins, thus ... High-Side Source Current from CP_OUT in Switch ON State IS 250 mA High-Side Gate Voltage VGATE_HS –0.3 to 65 V ... VCC2 can sustain load dump pulse of 40 V, 400 ms, 2.0 Ω. [2] In case of high current (SRC_HS >100 mA) and high voltage (>20 V) between GATE ...
Overview - Switch Pros
switchpros.comSP9100 8-Switch Programmable Switch Panel Power System ... To figure out the current draw of a load rated in watts, simply divide power rating of the accessory by the operating ... The other option is to program individual switches to be “battery controlled”. When “battery controlled,” the switches will operate at all times.
28 V, 56 mΩ, Load Switch with Programmable Current Limit ...
www.vishay.comthe SiP32419, the switch will remain off and the fault flag will remain on. The switch will be reset by toggling either control signal on EN pin or the input power if it is not under over temperature fault condition. These devices feature a low voltage control logic interface which can be controlled without the need for level shifting.